0
What else can I help you with?
What will a 3000 watt amp do to a 300 watt speaker?
Using a 3000 watt amp with a 300 watt speaker can potentially damage the speaker due to overpowering it. The excessive power can cause the speaker to blow out or distort the sound quality. It's important to match the power ratings of the amp and speaker to prevent damage.
Will a 600 watt amplifer power a 1300 watt speaker.?
Yes, but not to full effect.
If you mix a 1000 watt speaker with a 2500 watt speaker will they make a 3500 watt speaker?
No.
Can a 800va UPS load an 550va PSU plus CRT monitor?
This is pushing it, but it might be possible. If the PC has a 550 Watt power supply, then if you monitor pulls 250 Watts or less, it should work. You would likely do better if you had a LED/LCD monitor with this PC and backup power supply. Of course, the 550 Watt power supply shouldn't be pulling that all the time.
How much watt amplifier should be used to run 800 rms subwoofers 2 ten inch 400rms each?
1600 watt amp. your power amp should 2x the rms value. To varify, check JBL's website and look in one of their speaker manuals, it will show you their speaker wattage and then show you the recommended power amp wattage.
Should watt be capitalized?
Yes, "Watt" should be capitalized when referring to the unit of power, named after James Watt.
How many watts should a receiver have for 2000 Watt Speaker system?
For a 2000-watt speaker system, the receiver should ideally have a power rating that matches or exceeds the speaker's capacity to ensure optimal performance and avoid distortion. A general rule of thumb is to aim for a receiver with a power rating of at least 50-75% of the speaker's wattage. Therefore, a receiver with around 1000 to 1500 watts would be suitable, depending on usage and listening preferences. However, it's also important to consider the impedance and efficiency of the speakers and receiver.
Can a 1200 watt amp power a 1300 watt sub?
It's actually a good idea to have a speaker that can handle higher wattage than the amp can produce.
If you buy a two sub woofers with 400 Watt continuous and 1200 watt peak power how many watt amp should you buy?
800 watt should be fine
Is a 1000 watt power amplifier enough to power a 1000 watt subwoofer?
watt rating of a speaker is max power it can handle without getting damaged. it will produce proportionate amount of sound for less power from amp., even for 1 watt.The power output ratings for most amplifiers are very misleading. That number,i.e.,1000 watt , is under one certain type of condition for 1 second. Usually the frequency of 1khz for 1 second. The true output under actual operating conditions 20hz-20Khz is probably closer to 100 actual watts of music power or sound reproduction power. The same with the speaker rating,,,the power rated is at the same conditions Max power @ certain frequency @ certain amount of time.Safest bet,,,,,always use a larger rated speaker for an amplifier. If you have a 200 watt amp,,,use a speaker rated a minimum of 200 watts,,,,400 is better.
Can you use a 52 watt stereo with 1000 watt speakers?
sure you can, your amp will only deliver 52 watts to the speaker, more importend would be the impedance of the speaker . it should be equal to what your amp has! may be 8 ohms
If you buy a 180 watt sterio and want four speakers do you need to buy 45 watt speakers?
Yes. That would be the ideal wattage. When if comes to watts you don't want to wire speakers to a system that will push more wattage than they can handle. Think of watts as an amount of power. If you push more power through to the speakers than they can handle than you'll blow them. Example: [Stereo]-----60watts------>[Speaker with 45 watt capacity] = Not good. You can wire a speaker with a higher wattage capacity than what the stero will put out. Example: [Stereo]-----60watts------>[Speaker with 60 watt capacity] = Good. Example: [Stereo]-----60watts------>[Speaker with 75 watt capacity] = Good too.
