0
Top up with correct water anty-freze mix, take cap off expansion tank, turn on engine and allow to idle for 3 minuets or so, you can watch the bubbles coming up in the expansion tank. strongly massage the return pipe, big pipe on the top of the rad left side as you face it, coolant should shoot into the expansion tank as you do this. once it is cool check if you need to top up coolant mix and off you go.
ps do not take the cap of the expansion tank when the engine is hot.
Wiki User
∙ 11y ago
Add your answer:
Earn +20 pts
How do you bleed a cooling system on 2000 land rover range rover?
The Land Rover systems are self bleeding, just fill the header tank with water, then run the car while topping the tank up as the car pumps the water around the engine. Then go for a drive and ensure the heater is hot and check the water level when you return. If you have a re-occurring problem of air in your water system it would not be uncommon to have a blown head gasket or a cracked engine block.
How do you bleed water pipes on Peugeot 806?
how do I bleed water system on the 806 peugeot
What would cause pressure buildup and overheating in a range rover 4.6 after replacing the thermostat radiator cap and a radiator hose?
clog in radiator. drain radiator by removing cap on bottom remove cap on top fill top with water see if drains out bottom. or possibly an air pocket trapped in cooling system. make sure to bleed the air from the system.
How to bleed water pump on a 94 camaro 3.4 v6?
You don't bleed the water pump, you bleed the cooling system. Just jack up the front of the car or park it on an uphill incline and remove the radiator cap. Start the engine and let it run until no more air bubbles are escaping from the radiator. If it has bleeder valves use them to bleed the system. The water pump will bleed right along with the rest of the system.
What is a bleeder valve in a home water system?
A valve to bleed out air manually
From what would water and coolant be leaking from back side of the engine of a 1990 classic range rover?
Heater hoses? freez plugs
How to Locate 1993 rover 214 thermostat?
Oh those are really good fun rear of the engine is a black pipe approx 2" diameter where this pipe fits to the water pump is where you will find it I wish you the best of luck as these are hard to get to don't forget to bleed the system after you have changed the stat
How you change the water pump on a Land Rover discovery?
How do you remove a water pump on a 2002 land rover
Do the thermostat have to be on to bleed home radiator?
on hot water heat with a boiler you should pressurize the system then open the bleeders
How do you properly bleed cooling system on 1996 olds cutlass?
To bleed the cooling system on a 1996 Olds Cutlass, locate the bleed valve, which is on the front of the engine above the water pump. After making sure the cooling system is not under pressure, open the valve by turning it counterclockwise. Fill the radiator with coolant until no air comes out the bleed valve, and a stream of coolant begins to flow from there instead. Tighten the valve and close the system to finish the job.
How do you bleed the water system on pug 106?
Look for a plastic cap, looks like a dustcap on the wheel, unscrew and squeeze the bottom pipe until water is coming out, have an assistant replace the cap while you are squeezing. you can also unscrew a plug the the top of the rad an bleed it that way or u could unscrew a allenkey bolt on top of the water pump that will also bleed tha system Stoatwblr: You should bleed at all 3 points as they're all air traps. Loosen all 3 points, then tighten them up as water starts to flow from them (there will be a few bubbles to start with, wait till those stop). The order for filling is radiator, water pump, bleed cap (water flows to lowest point first, etc etc.)
How do you bleed a sprinkler system?
Bleeding a sprinkler system involves draining the existing water from the pipes. Afterwards, the pipes should be completely dried by using an air compressor.
