0
You don't bleed the water pump, you bleed the cooling system. Just jack up the front of the car or park it on an uphill incline and remove the radiator cap. Start the engine and let it run until no more air bubbles are escaping from the radiator. If it has bleeder valves use them to bleed the system. The water pump will bleed right along with the rest of the system.
Wiki User
∙ 17y ago
Add your answer:
Earn +20 pts
How do you remove a water pump pulley on a 2001 dodge ram 34 ton 4X4 5.9 liter engine?
The pulley is pressed fit onto the pump. It will not come off the pump. You have to replace the pump to replace it.
Is it ok to reduce the inlet of a pump from 34 to 12 if the hole in the pump's inlet is 38 ID with 34 thread?
Itll work' just not as efficiently
A pump can supply 5 units of water per minute How many minutes will it take to fill a 600 unit tank to its full capacity if it is already 34 full of water?
30 minutes but depending on your pump and how much back pressure on the pump line when it begins to reach full capacity of your tank well reduce your pump supply.
Why does my 1989 camaro have a code 34?
mass air flow sensor or manifold pressure sensor. your car will have either or.
1995 34 camaro is making a rattling noise under car?
Inspect the catalytic converter heat shield.
Why does your 1989 camaro have a code 54 and 34 after you replaced the mass air and fuel pump relay you also replaced the computer?
I woulda thought to reset the computer but I guess a new one would have taken care of that. Did you check all the wiring for the 2 components? I can only think that its shorted somewhere in there.
Where is the speedometer cable on a 1994 Chevy Camaro 34 V6?
it doesn't have one it is electric uses a vehicle speed sensor on rear of trans.
Water pump replacement in a 2005 chevy impala?
Water Pump Replacement (3.4L)Removal ProcedureDrain the cooling system. Refer to Cooling System Draining and Filling.Remove the drive belt shield bolt.Remove the drive belt shield.Loosen the water pump pulley bolts.Remove the drive belt. Refer to Drive Belt Replacement for the 3.4L engine.Remove the water pump pulley bolts.Remove the water pump pulley.Remove the water pump bolts.Remove the water pump (1).Remove the water pump gasket (2).Clean the water pump gasket mating surfaces.Installation ProcedureInstall the water pump gasket (2).Install the water pump (1). Notice: Refer to Fastener Notice in the Preface section.Install the water pump bolts. TightenTighten the bolts to 10 N·m (89 lb in).Install the water pump pulley.Install the water pump pulley bolts. TightenTighten the bolts to 25 N·m (18 lb ft).Install the drive belt. Refer to Drive Belt Replacement for the 3.4L engine.Install the drive belt shield.Install the drive belt shield bolt. TightenTighten the bolt to 10 N·m (89 lb in).Fill the cooling system. Refer to Cooling System Draining and Filling./////////////////////////////////////////////////////////////////////////////////////////////////Water Pump Replacement (3.8L)Removal ProcedureDrain the cooling system. Refer to Cooling System Draining and Filling .Loosen the water pump pulley bolts.Remove the drive belt. Refer to Drive Belt Replacement in Engine Mechanical - 3.8L.Remove the water pump pulley bolts.Remove the water pump pulley.Remove the power steering pump and reposition. refer to Power Steering Pump Replacement in Power Steering System.Remove the water pump bolts.Remove the water pump.Remove the water pump gasket.Clean and inspect the water pump mating surfaces.Installation ProcedureInstall the water pump gasket.Install the water pump.Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.Install the water pump bolts. Tighten• Tighten the long water pump bolts to 34 N·m (25 lb ft). • Tighten the short water pump bolts to 22 N·m (16 lb ft).Install the water pump pulley.Install the water pump pulley bolts. TightenTighten the bolts to 13 N·m (115 lb in).Install the power steering pump. Refer to Power Steering Pump Replacement in Power Steering System.Install the drive belt. Refer to Drive Belt Replacement in Engine Mechanical - 3.8L.Fill the cooling system. Refer to Cooling System Draining and Filling .
What are the release dates for 60 Minutes - 1968 The Pump LBJ Tapes Con Man 34-40?
60 Minutes - 1968 The Pump LBJ Tapes Con Man 34-40 was released on: USA: 23 June 2002
How much is 34 cubic kilometers of water?
It equals exactly that, 34 cubic kilometres of water!What do you actually want to know?
How many teaspoons is in 34 g?
34 grams of water is about 6.8 teaspoons
Who sang wait and bleed from slipknot?
The lead singer Corey Taylor did. At 2:34 Clown did the growling in the background.
