KEYLESS ENTRY SYSTEM
With the keyless entry keypad, you can:
• lock or unlock the vehicle doors
without using the key.
Your vehicle has a factory set 5 digit
code that operates the keyless entry
system. You can also program your
own 5 digit personal entry code. The factory-set code is located:
• on the owner's wallet card in the glove compartment
• or at your dealer.
When pressing the controls on the keyless entry keypad, press the
middle of the controls to ensure a good activation.
This system will disable the power door lock controls. These will not
work until the vehicle is disarmed.
Programming your own personal entry code
To program your own code:
5. Enter factory set code (keypad will illuminate when pressed).
6. Press 1/2 control within five seconds of step 1.
7. Enter your personal 5 digit code.
Enter each digit within five seconds
of previous one.
8. After the code is entered, the
locks will cycle, confirming that the
new code has been set.
Do not set a code that includes five of the same number or presents
them in sequential order. Thieves can easily figure out these types of
codes.
Your personal code does not replace the permanent code that the
dealership gave you. You can use either code to unlock your vehicle. If a
second personal code is entered, the module will erase the first personal
code in favor of the new code.
Locks and Security
149
Locks and Security
If you wish to erase your personal code, use the following instructions:
1. Enter factory set code.
2. Press 1/2 control and release.
The system will now only respond
to the factory set code.
Anti-scan feature
The anti-scan feature prevents
repeated attempts at arriving at a valid key code.
The keyless entry pad is disabled for 1 minute after 7 unsuccessful
attempts (35 consecutive button presses) at entering a valid key code.
The keypad will flash during this 1 minute mode. However, the 7/8 and
9/0 controls will still lock the vehicle.
Anti-scan will be turned off after:
• one minute of keypad inactivity.
• the remote entry transmitter UNLOCK button is pressed.
• the ignition is turned to the ON position.
Unlocking the doors with the keyless entry system
To unlock the driver door, enter either the factory set code or the
personal code (each digit must be pressed within five seconds of the
prior digit). The interior lamps will also illuminate.
To unlock all doors, enter the factory set code or personal code (driver
door unlocks) and press the 3/4 control within five seconds.
Locking the doors with the
keyless entry system
It is not necessary to enter the
factory or personal code prior to
locking all doors. To lock the doors:
• with the driver's door closed, press the 7/8 control and the 9/0 control
at the same time.
Locks and Security
150
the keyless entry code is inside the cover in the back where the rear windshield washer container is
I have a 1998 and the code is in the back where your jack and accessories are.
The code is on a sticker on the top of the control module.
Keyless entry codes for most makes and models can be obtained from a dealership with the VIN number and identification. If the code has been changed by a third party then the dealership will not be able to retrieve it.?æ
there is a "wallet card" which has the code on it, if you do not have this card you will need to bring the car into a Mercury dealer and they will "plug it in" and retrieve the factory preset code.
My code was located in the compartment with my jack. It is on the side of the white computer box. Hope this helps.
sticker in the glove comparment or you can program your own with the manual or go to the dealer,they might charge for it.
Keyless entry will have a keypad built into the driver's door handle.
how do you change the battery in a 2002 jetta keyless entry pad?
codes on my 2001 were located behind the passenger side rear seat seat belt panel. I got instructions off EBay for $15. Well worth it.
its on a little card in the glove box
first u need to know the original key code.. if u do not have it, u can go to a service center and they can put yer car on the computer and that wil tell them the factory code. once u have that then u will be able to change the code to anything u want..