0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
Why dp created for flow measurement?
The primary element creates a pressure drop across the flow meter by introducing a restriction in the pipe, and this engineered restriction enables Bernoulli's equation to be used for a flow rate calculation.
What is DP in welding process?
DP is not actually to do with welding it is a form of NDT which stands for non destructive testing; DP is dye-pen where a white liquid formation is placed over the weld & a normally red enhancer is then placed over the top; this then identifies surface cracks.
What is DP steel?
dual phase steel is a high strength steel that has a ferrite and martensitic microstructure
Design calculation of chimney height with respect to boiler horsepower?
dp=Cah(1/T0-1/T1)
A differential pressure transmitter is to be calibrated to read level of a closed vessel The dimensions of the closed vessel are as given below What would be the calibration range of the transmitter?
Dp= rho * g * Dh Dp = differential pressure between point 1 and point 2 [Pa] rho = density of the liquid [kg/m3] g = gravity accelaration [m/s2] Dh= height from point 1 to point 2 [m] For typical everyday sizes of rho and Dh, it can be easily seen than Dp is in the range of 1 to 50 kPa (10 to 500 mabr)
How do you calculate the steam flow rate?
Q=K Squareroot of (DP/SG) Q=Flow rate DP = Pressure diffrence (P1-P2) SG= Specific gravity
How to calculate square root in DP flow transmitters?
Don't stop believing'… hold onto that feelin'
Why dp created for flow measurement?
The primary element creates a pressure drop across the flow meter by introducing a restriction in the pipe, and this engineered restriction enables Bernoulli's equation to be used for a flow rate calculation.
How to calculate DP ratio?
Stock+debtors-creditors/sale
What is valve cv?
Cv is a capacity rating for a valve. A valve with a Cv = 1 will flow 1 gpm of water with a differential pressure of 1 psi. If the Cv was 100, it would flow 100 gpm of water with a 1 psi differential pressure. For non-flashing/cavitating service, Q = Cv * (dP/SG)^0.5. Q is the flow rate in gpm (US gal), dP is the differential pressure in psi and SG is the liquid's specific gravity.
How dp you calculate volume?
The answer depends on the shape and also on what information is provided, in what form.
What does cv rating mean on a water valve?
The CV value is the flow rate required to generate 1 psid of pressure loss through the valve. Since pressure drop follows a basic square law the relationship between Cv, flow and pressure loss is as follows: DP = k x Flow^2 eq 1 Where k is a constant that represents the flow shape in the wide open condition. Since Cv is the flow rate at 1 psi of pressure loss then it follows that DP = k x Cv^2 = 1 eq 2 solving for k from eq 2 yields k = 1/Cv^2 eq 3 substituting eq 3 into eq 1 yields DP = (Flow/Cv)^2 Now you have an equation that will tell you the pressure and flow relationship for that particular valve with a particular fully open Cv value. In short, the higher the Cv value the more flow the valve will allow for the same pressure loss or the less pressure loss for the same flow. Good luck
What is the formula for finding the permeability of materials?
The Darcy fluid flow equation: u = q / Ac = ( - k / µ . dp / dI ) Where: u = fluid velocity, cm/s. q = flow rate cm3/s k = permeability of the porous rock, Darcy (0.986923 µm2) Ac = cross-sectional area of the rock, cm2 µ = viscosity of the fluid, centipoises (cP) I = length of the rock sample, cm dp / dI = pressure gradient in the direction of the flow, atm/cm.
Difference between pressure regulating valve and differential pressure valve?
Pressure Differential Valve- maintains a constant Differential pressure across it. Say if P1 was inlet pressure and P2 was outlet pressure PDV will try to keep constant DP. Say if P2 increases due to some reason and P1 is constant the DP will decrease and will decrease flow through the PDV. At this point to maintain the constant DP PDV will open and allow more flow through to keep the flow constant and thus DP constant.
What is difference between profibus dp and profibus pa?
First I think I should point out that Profibus-PA instruments do not use RS-485 (such as is used by Profibus-DP), but a MBP (Manchester Coded, Bus Powered) physical layer, as described in the IEC 61158-2 standard. This is why you need a bus coupler to 'translate' the signals from Profibus-DP to Profibus-PA, and to power the PA bus. The maximum transmission rate of Profibus DP network 12Mbps The maximum transmission rate of Profibus PA network 45.45Kbps You need to power the DP instruments, while PA instruments get its power and exchange data via the same PA cable . You need DP/PA link or DP/PA coupler to link DP network with PA . when you use a coupler connected directly to the DP network , then your DP network transmission rate would be decreased to 45.45. From Pradip
How do you calculate the acres to meter square?
1 acre = 4046.8564 sq metres (to 4 dp)
How do you calculate equation with 6700000 as denominator and 11000000 as numerator?
11000000/6700000 = 110/67 = 1.6418 (to 4 dp).
