you can get a cold air intake some silver spark plug wires an upgraded coil pack or ignition coil whichever u have k&n air filters high performance fuel filter flowmaster exhaust system hollow out the converter and so forth just make sure once u reach a certain point you change out your rear end for a stronger rear end or you'll completely bust the guts
Fuel injected. fuel injected. the 3.8 liter was never carb. it was in the 80's in other GM vehicles
A haynes manual...
38L is 10.04 US gallons.
on the crank behind the front cover
it's located on the firewall right in back of the intake
Not very easily if at all, and why would you want to?
They always blow the head gaskets between 70 and 100 thousand miles.
If you mean 3.8 Litre engine, the answer is 200 horsepower, from the factory. 225 lb/ft of torque.
You can safely put 2ml into the 10l aquarium
there should be a sticker under the hood of the car that tells you what the gapping should be. .60
76l for the first fish and 38l for each additional fish so 266 litres.
Five quarts including filter. My owners manual says 5.75, including filter. My experience agrees with the extra .75 quarts! :)
Divide 10 by 38. _ _ ._ _ 38l 100 38 can't go into 10 so add a decimal+zero Then do your basic division. This was coming from a 6th grader.
One of the best places to start could be a dealership. If you don't want to go that route you can always look it up using a Haynes or Chilton repair manuals.
haynes repair manuals are good but you can go to autozone.com and they have online repair manuels as well it a good site for a lot of information on repair work.
There are 460 CID engine swap kits on SUMMITRACING.COM. The 460 is the building "block" for several larger stroker motors. It will take a lot of work. If you have all the necessary parts, it would take the average mechanic at least 6 weeks. Likely more. Unless you're going for a strictly track vehicle, you'd get more bang for your buck with a supercharged 4.6 or 5.0.
It shouldn't idle that high the factory idle setting is around 900 RPM's check to make sure nothing is sticking and check vacuum lines. Good luck fixing your problem.
The 3.8 engine is similar in all the grand prix 97 to 2003 Follow the top radiator hose to the top of the engine, the place it bolts up to should be your themostat. Remove the hose, take the bolts out (usually two) put the new one in with a new gasket and bolt it back together. For thermostat replacement step by step instructions with pics- http://www.pfyc.com/supportfiles/tstat/tstat.htm Hope this helps. "G"
The mass air flow sensor is located in the throttle body housing on the 3800 engine. There should be 4 screws that hold it down to the housing. Once they screws are removed, the sensor lifts off of the throttle body.
There is not significant difference between rest cardiac output but during the load amateur heart pumps 18-24 l/min, professional heart pumps 32-38l/min.
Yes you can, you will need to buy a y pipe either at autozone or your nearest parts store. You will also need to buy 2 mufflers flowmasters are my choice but you decide what you want. then buy some cool tips and there you go.
Where was the leak coming from? the coolant has some pathways that go to the intake. that's to warm up the air.the most important question is where the coolant was leaking from?
Yes , on a 1998 Ford Windstar the fuel pump shut off switch ( inertia switch ) is in the drivers footwell behind the kick panel by the drivers left foot , by the inside hood release ( there is an access hole in the panel )
Had the same problem years ago, same year, model. Found the cable at NAPA auto supply, about $30, much cheaper than the GM dealer. Couldn't do the replacement myself, had to have a mechanic do it (it was a B***H). Still cheaper in the long run this way.