0
What else can I help you with?
Why do cars use belts and pulleys?
It transfers power from the alternator to the crankshaft and the camshaft to make your engine work.
How do you convert from a generator to alternator on a 1963 Ford Falcon 170 ci engine?
The easyest way is to go with a 1 wire alternator (self exciting). Find or make brackets that will work, mount the alternator and run 1 wire from the alternator to the battery.
What in a automobile engine serves no purpose but without it the engine does not work?
Noise. Without noise, it can't work. Noise is in an engine, and without it does not work. Every engine has to make some kind of noise, internal or external, inside or outside the engine.
What is wrong if the engine would jump start but other controls on the dashboard did not work and the engine died after removing the jumper cable?
Battery is completely discharged or is defective. loose alternator wiring or bad alternator.
How do you remove alternator on 1994 diamante?
Before removing the alternator and bracket assembly from the engine, loosen the assembly bolt by which the alternator is fixed at the alternator bracket. There is only a small amount of room in which to take out the alternator so you will have to work very carefully with it to prevent damaging nearby components. NOTE: If this is a SOHC engine then remove the alternator through the transaxle side, through the bottom of the intake manifold plenum.
Would a bad alternator make the wipers not work on 1995 altima Nissan?
no if your battery light is on and the brake light on then your alternator need to be change
Will alternator still work if the gauge is not?
An alternator does not need a gauge to work. It is used to monitor the output of the alternator.
Where is the alternator on 2004 Colorado?
On a 2004 Chevrolet Colorado, the alternator is located on the engine's front, typically on the driver's side. It's mounted near the top of the engine, making it accessible for maintenance. To reach it, you may need to remove any components obstructing access, such as the serpentine belt. Always ensure the engine is off and cool before attempting any work on the alternator.
Where is the alternator on a 2004 Mazda 6?
The alternator on a 2004 Mazda 6 is located on the front side of the engine, near the top, typically on the passenger side. To access it, you may need to remove the plastic engine cover and possibly some other components for better visibility and clearance. It's connected to the battery and the engine with wiring and a belt. Make sure to disconnect the battery before attempting any work on it.
What is the purpose of the fan or alternator belt?
Any belt in a car assists in moving all parts within the engine to work in providing power and cooling to vehicle. The alternator provides power to the battery and the fan cools the radiator so the engine will not overheat.
How do you put an alternator belt on a 1992 Geo Storm?
your belt tensioner is built in on the mounting bracket off the engine. you will only find two bolts that hold on the alternator to the engine, one is a pivot hinge, a long bolt that if loosened will allow the alternator to move away or closer to the engine, (tension). the other is on a sliding bracket on the front of the alternator that works with the pivot bolt. i can't remember whether its a 14 or 12 mm bolt. either way, just loosen both of the bolts, hammer or pry the alternator towards the engine, slip on the belt. make sure the belt fits into the grooves properly, then pry the alternator away from the engine. make sure the belt is extremely tight. i just replaced mine and i didn't pry hard enough and it slipped off halfway to a friends house, (not fun). anywas it's best to have someone pry the alternator and you tighten the bolts. in order to replace the alternator belt you have to remove the ac and power steering pump belt. both the ac compressor and the power steering pump work the same way as the alternator. loosen them bolts and hammer or pry them towards the engine to slip it off. good luck. i know i needed it. your belt tensioner is built in on the mounting bracket off the engine. you will only find two bolts that hold on the alternator to the engine, one is a pivot hinge, a long bolt that if loosened will allow the alternator to move away or closer to the engine, (tension). the other is on a sliding bracket on the front of the alternator that works with the pivot bolt. i can't remember whether its a 14 or 12 mm bolt. either way, just loosen both of the bolts, hammer or pry the alternator towards the engine, slip on the belt. make sure the belt fits into the grooves properly, then pry the alternator away from the engine. make sure the belt is extremely tight. i just replaced mine and i didn't pry hard enough and it slipped off halfway to a friends house, (not fun). anywas it's best to have someone pry the alternator and you tighten the bolts. in order to replace the alternator belt you have to remove the ac and power steering pump belt. both the ac compressor and the power steering pump work the same way as the alternator. loosen them bolts and hammer or pry them towards the engine to slip it off. good luck. i know i needed it.
Can a Chevy S-10 blazer alternator work with a Chevy S-10 truck?
Yes, as long as they have the same engine
