0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
How do you wire a 220v dryer to run on 110?
You can't. A 220 volt dryer requires 220 volts in order to operate properly. It will not run on 110 volts.
What is the proper type of meter for testing a GCFI receptacle?
Any electrical meter which measures volts or a standard plug tester. (the ones which plug into the receptacle and light up indicator lights) As long as the receptacle measures 110-120V between the hot and neutral, and measures 110-120V between the hot and ground, then it is wired correctly and supplying correct voltage with ground reference. To determine if the GFCI is "tripping" or opening the circuit when it should, simply press the test button. If it doesn't trip, (or reset correctly with the reset button) replace the device.
How much power is a hair dryer using if it operates at a voltage of 110 volts and has a current of 6 amps?
About 660 watts. A hair dryer has a small blower motor and a resistance winding that heats up. The formula is watts = volts x amps x power factor. In the case of a resistive load like the wire that heats up the PF = 1. However, the blower will have a lower PF of about .8.
Can resistors be used to use a 110 volts rated hairdryer in a 220 volt source?
Resistors could be used if you can find resistors with a high enough wattage rating to dissipate the heat that they will generate. Your best bet is to purchase a voltage adapter. The adapter is just a transformer that steps down the voltage from 220 to 110 volts. Locate on the hair dryer what the wattage draw is and then match the transformer (adaptor) to that wattage output.
What current flows through a hair dryer plugged into a 110 volt circuit if it has a resistance of 25 ohms?
Ohm's Law: Current is voltage divided by resistance110 volts divided by 25 ohms is 4.4 amperes. This is also 440 watts, which sounds low in today's design of hair dryers, leading one to think that the 25 ohms is incorrect or was measured incorrectly.
Can you change a dryer plug to fit a regular wall plug?
Different plugs are designed so that you can't plug an appliance into the wrong voltage. A dryer is usually 220-240 Volts and your standard outlet is 110-120 Volts. You can't do what you suggest.
Is it easy to change a 110 plug over to a 220 plug for a dryer?
No, it is more difficult than installing a new plug. You cannot reuse the wire, it must be a dedicated circuit, you will need a new outlet, and you will need a new breaker. Install a new plug.
Can you plug a V into a V?
can you plug a 115 volt into a 110 volt
When you plug a 110 volt into a 110 wall plug and hit start it throws the breaker why?
There is a direct short after the switch.
Can you use European appliances in the US?
Yes, but you need a converter that changes 220 to 110, if you plug it into a 110 plug. Of course, if you plug it into a 220 outlet you don't need a converter, but in either case you will need a plug adapter.
Can you plug In a 220 volt to a 110 outlet?
no
Can you plug 110 volt appliance into 12 volt?
NO
Can you plug your washer and dryer into the same socket?
No. They are two different voltage and amperage rated pieces of equipment. Also, a dryer does not use a common (neutral) wire. It uses two separate 110 volt legs, and a ground. The washer uses only one 110 volt leg, a neutral, and a ground.
Where do you plug in US appliances?
You can plug US appliances into plug sockets in the US. You can also plug them into sockets in Mexico, Canada and several other countries that use 110 to 120 volts mains electricity.
1992 Saturn where the engine block heater plug is located the 110 plug?
where is the heater block on a 2004 saturn vue?
Can you change 32 amp 110v plug to a 16 amp 110 v plug?
Provided the equipment draws less than 16 amps it can be supplied from a 16 A plug.
Spark plug gap for a Honda atc 110?
.025
