answersLogoWhite
Audi A4

How can you replace a brake lamp in an 2003 Audi A4?

212223

Top Answer
User Avatar
Wiki User
2007-11-03 18:29:24
2007-11-03 18:29:24

ben a while since i did one of these but im sure you have to remove the whole light cluster to change a bulb. Inside the boot you should find a bolt, undo the bolt and the light will be loose but be careful because the top is held in by a plastic dowel on lamp, too rough and you will snap the lug.

1

Related Questions

User Avatar

It's an yellow warning indicator lamp. It lights when brake pads are weared. Now it's time to replace the used brake pads!

User Avatar

Which brake lamp are you needing to change? Brake/turn signal lamp.

User Avatar

if it isn't a fuse or lamp problem, check the brake lamp switch on the brake pedal, if you unplug the switch, and jumper the connection, and you have brake lamps, replace the switch...

User Avatar

the 1989 Honda accord lxi has a brake lamp light on the dashboard, if the brake lamp light is on, this means you have a brake/tail light out or disconnected

User Avatar

check the switch on the top of the brake pedal.

User Avatar

2009 Audi A4 brake light bulb lamp replacement procedure: Purchase the correct replacement brake light bulb(s) first, before disassembling the vehicle. See sources and related links below for replacement brake light bulb information. Then consult your owner's manual for the replacement procedure. As simple as it sounds, the owner's manual is the best place to start for brake light bulb lamp replacement instructions and illustrations. You may want to consider replacing both left and right at the same time in order to keep brightness and color equal (optional).

User Avatar

The light assy has to be removed to take the bulbs out.

User Avatar

One or both your break lights are no longer working.

User Avatar

Replace the brake lamp (the one on the right that doesn't go on). Go to a local autoparts store to buy the bulb (usually not more than a few dollars). They might even help you replace it. If it was just a burnt-out bulb, the brake lamp light on the dash should go out once the bulb is working again.

User Avatar

The lamp in the top brake light of a Toyota Highlander can be replaced by the locating the light housing from the trunk. Find the light cover and remove it to access the lights. Replace the bulbs.

User Avatar

If "safety lamp" is actually referring to the high-mount / center brake light, see "Related Questions" below for more

User Avatar

2003 Hyundai Elantra brake light bulb lamp replacement: Purchase the correct replacement brake light bulb(s) first, before disassembling the vehicle. See sources and related links below for replacement brake light bulb information. Then consult your owner's manual for the replacement procedure. As simple as it sounds, the owner's manual is the best place to start for brake light bulb lamp replacement instructions and illustrations. You may want to consider replacing both left and right at the same time in order to keep brightness and color equal (optional).

User Avatar

2003 Lincoln LS brake light bulb lamp replacement: Purchase the correct replacement brake light bulb(s) first, before disassembling the vehicle. See sources and related links below for replacement brake light bulb information. Then consult your owner's manual for the replacement procedure. As simple as it sounds, the owner's manual is the best place to start for brake light bulb lamp replacement instructions and illustrations. You may want to consider replacing both left and right at the same time in order to keep brightness and color equal (optional).

User Avatar

01 Yukon 3rd brake light removal......changing the third brake light on a 2001 Yukon is a relatively easy task. First open the rear liftgate (not just the glass). This will expose the two screws that secure the housing of the lamp to the body (it also exposes the connector plug which, obviously, you should unplug). After removing the two screws, separate the rubber housing from the LED lamp itself....and there you have it!...because the third brake light is a sealed lamp the entire brake light must be changed. you can�t just replace the bulbs. ...

User Avatar

Check to see if Brake lamps work when brake pedal is pressed. If not gear shifter is locked for safety so replace fuse or repair brake lamp switch.

User Avatar

The brake, turn signal, back-up, and side marker lamps are incorporated in the tail lamp. # Remove the screws attaching the lamp to body . # Disengage the lamp from the alignment pin. # Disconnect lamp wire harness connector. # Separate lamp from vehicle. The brake, turn signal, back-up, and side marker lamp bulbs are incorporated into the tail lamp. # Remove the tail lamp. # Rotate the bulb socket counterclockwise. # Separate the socket from the lamp # Remove the bulb from the socket

User Avatar

How do you replace interior door courtesy lamp?

User Avatar

On a 1994 Honda Accord, the brake lamp comes on when a tail light is no longer working. The burned-out bulb needs to be replaced. The brake lamp will not come on after the bulb is replaced.

User Avatar

The stop lamp switch is on a bracket above the brake pedal.The stop lamp switch is on a bracket above the brake pedal.

User Avatar

The dash cluster has to be removed or partially anyway to get to the bulb. Usually there are about four to six screws depending on the model. good luck


Copyright © 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.