0
One old trick to solder two wires is to twist them together and twist some solder round them as well, wrap them in foil and apply a lighted match.
Wiki User
∙ 9y ago
Add your answer:
Earn +20 pts
Tools used for soldering?
The main tools for soldering include a soldering iron, a stand for the soldering iron, and solder. You'd likely use other tools such as brushes, picks, heat sinks, solder wick, desoldering irons, etc.
How do you break in a new soldering iron?
Look at the 'bit', the part that gets hot that you do the soldering with. It should have an inclined flat surface on the end. If it has not, make one by using a file. Heat the soldering iron up. At the same time get the solder out, which should be tin solder with internal flux. When the iron is hot, quickly file the surface of the bit clean and apply the solder, which should immediately 'take' to the surface. That's it.
What is a solder remover?
Solder remover is an object or device for removing solder, usually from printed circuit boards. It can be in the form of a copper mesh called solder wick, a separate vacuum device you use alongside a soldering iron, or a desoldering iron. A desoldering iron gets hot like a soldering iron, but the tip is hollow and there is a squeeze bulb mounted on top. So you heat up the solder on the board and then use the bulb to vacuum up the solder and then deposit in a safe place such as a can or ash tray.
What is a soldering iron stand?
First of all, solder is metal alloy with a low melting point at 200 to 840 degrees Fahrenheit. A soldering iron is a tool used to metal solder to join two metal objects together. Therefore a stand for an soldering iron would just hold it. They usually have metal springs to hold the iron, obviously with a higher metaling temperature. This is a link to a picture of a soldering iron holder: http://www.qwikfast.co.uk/catalogue/images/silvsoldironstand427552.jpg
What is cold flow?
It is a term used when soldering with a soldering iron. It means that the solder is not completely up to temperature to make a proper joint. A good solder joint is very silvery in colour and shines when it is done right.
How to sauder wire without sauder iron?
You can solder wires without a soldering iron using a lighter.
What is iron tin?
Tinning the Soldering iron is when the hot iron is coated with solder to aid in soldering and heat transfer
What tools are needed to solder circuit boards?
Soldering iron, solder, flux
Tools used for soldering?
The main tools for soldering include a soldering iron, a stand for the soldering iron, and solder. You'd likely use other tools such as brushes, picks, heat sinks, solder wick, desoldering irons, etc.
How do you stolder?
Solder. You'll need a soldering iron, for starters.
What equipments are there in soldering?
There is a lot of equipment in Soldering and I am telling you about which I know. Soldering Iron You can’t do soldering without a soldering iron/gun. But you don’t have to buy an expensive soldering iron/gun. You can find soldering irons in less than $10 that would work for most beginners’ needs. Wire Cutter The wire cutter is a very handy little soldering tool. We mostly use it to cut long component legs, or to strip the end of a wire. Wire Cutters is also known as flush-cutters, diagonal cutters, electronic snippers, clippers, etc. Wet Sponge A wet sponge is very useful for cleaning the tip of the soldering iron. The tip is hot which means it will oxidize very fast and get dirty. A clean tip transfers heat faster and makes your soldering easier. A sponge is so cheap anyway, so you should always keep one together with your other soldering tools. Soldering Stand A soldering iron gets hot after performing soldering, so it’s important to place it in a safe way in between soldering. A soldering iron stand is very useful for this. Since it takes up a lot of space, I don’t bring mine when travelling, but I always have one at my desk in Illinois. Safety Glasses A pair of safety glasses is something I really recommend when you do soldering. The consequences of getting hot soldering splashed into your eye can be terrible. So, please use them. Tweezers Tweezers are great. You can use them to keep components in their place and to avoid burning your fingers when you do soldering. If you ever solder surface mount components, these are very useful for placing small components. Solder wick The solder wick is another tool for removing solder. It’s made up of copper threads that will absorb the solder from the solder joint. For example to remove “solder bridges” between pins on a chip or if there’s a bit of solder left on a bigger solder joint.
Can you mend exhausts by soldering?
Welding or brazing perhapsReplacement is best Solder has too low a melting point to be good in such a high temperature environment. After running the car for a few miles, you could apply the solder to the muffler and it will melt without a torch or soldering iron.
What is the characteristic of soldering iron?
Thre two types of soldering iron are straight and hatchet soldering iron
How do you break in a new soldering iron?
Look at the 'bit', the part that gets hot that you do the soldering with. It should have an inclined flat surface on the end. If it has not, make one by using a file. Heat the soldering iron up. At the same time get the solder out, which should be tin solder with internal flux. When the iron is hot, quickly file the surface of the bit clean and apply the solder, which should immediately 'take' to the surface. That's it.
How to solder wire without a solder iron?
It is difficult to solder without the soldering iron, but not impossible. So, let’s talk about how to solder without a soldering iron. Getting a Heat Source Since you don’t have a soldering iron, you are going to need a heat source to heat up the various parts and the solder itself. In this case, it means having an open flame or heat source to provide the heat needed to melt the parts. The most important thing to keep in mind is that your heat source needs to be able to heat up the solder to its melting point, which is going to be between 400° and 700° Fahrenheit, or about 200° to 370° Celsius. Things like normal butane lighters, oil lamps, alcohol burners, candles, and even open flames like a campfire should do just fine for this task. Some people even choose to use a thick tin can and create a small and contained fire inside. As long as your heat source can melt the solder, you will be fine. Soldering by Heating the Wires Directly The easiest way to solder with a soldering iron is to twist the wires together and heat them directly. It doesn’t require a soldering iron and is quite easy to do. If you are soldering wires, strip the insulation off the ends of the wires to be soldered together. Now, twist the ends of the wires together with a few rotations. Make sure that the wires are twisted tightly together. What you want to do here is to heat up the wires using your open flame. Make sure to not heat up the insulation past the exposed wires too much, as this can cause its own problems. Let the twisted wires heat up for about 20 seconds, then slowly apply a thin layer of solder to them. The solder should melt right onto the wires, but if it does not, heat up the wires more to make it melt. You don’t want a cold solder joint as these are not effective. Now that you have the solder connection, you can cut off the rest of the exposed wires past the point of the solder. Using Small or Large Heat Sources for Soldering If you are working with a small heat source, such as a candle or a lighter, you need to use a small soldering iron, like the tip of old scissors. The best thing is 14-gauge steel wire, as it heats fast, but retains heat fast enough to solder with. The wire is easy to bend into shape for various soldering positions. Nails and screwdrivers work too. Now you want to use your lighter or candle to heat the soldering tool of choice. Heat it about ½ inch from the very tip, as this will help prevent damage and oxidation. Allow the wire, nail, or other soldering tool of choice to heat up for about 20 seconds, then move quickly to solder the components that require soldering. If necessary, keep repeating this process until you are done. Conclusion is that it is not impossible to work on solder without soldering iron.
How do you use a soldering iron?
To use a soldering iron, you must have a piece of solder, something to cool it down, eg a damp sponge and a mains plug socket.You must plug in the soldering iron and push the switch. Then, you must take your piece of solder, and with the soldering iron in one hand (Preferably your strongest hand) and your piece of solder in the other, you need to heat the tip of the soldering iron by feeding your piece of solder through the curved part of the soldering iron. This will melt the tip of the solder, and once you have melted about 5 millimetres, you are ready to go.You need to use your piece of solder to feed through the soldering iron once again, but this time, the melted solder (the gooy gray stuff) that comes out needs to be applied to the two pieces of metal you want to solder together. Once you have used about 2 centimetres of solder, the melted solder will have hopefully made a mountain shape that curves around the two pieces. Solder freezes VERY quickly so you only have to leave it for about 5-10 seconds, then give it a firm pull, and it should remain intact.ANSWER: The sponge is not to cool it down but rather to clean the tip from operation to operation. To begin with apply solder to the tip to tin it. Always use the right iron for the job. The idea is to melt the solder and make a good connection without heating and destroying the part. A good solder connection is a shiny connection. The application of solder flux will help the solder to flow and displace material present. There is no time limit or set time if it takes too long you got the wrong iron needs more heat in that case or a clean tip.prepare the items to be soldered so that they make a solid mechanical contactclean the surfaces with flux (if you are using "cored solder" this happens automatically)begin heating the items to be soldered with the soldering ironmelt a little bit of solder between the soldering iron and the items to be solderedas soon as the items to be soldered are hot enough to melt solder themselves melt solder into themimmediately remove the soldering iron and let the joint coolif the joint has smooth shiny surfaces you are done, otherwise the joint will be rough and crystalline looking (this is called a "cold joint") and you will have to apply more flux remelt it with the soldering iron and sometimes add a bit more solder. oddly enough a common cause of "cold joints" is overheating and burning off the flux you applied
What is a solder remover?
Solder remover is an object or device for removing solder, usually from printed circuit boards. It can be in the form of a copper mesh called solder wick, a separate vacuum device you use alongside a soldering iron, or a desoldering iron. A desoldering iron gets hot like a soldering iron, but the tip is hollow and there is a squeeze bulb mounted on top. So you heat up the solder on the board and then use the bulb to vacuum up the solder and then deposit in a safe place such as a can or ash tray.
