To terminate a 3 wire wye motor to a 3 phase delta connection you need a 3 phase transformer to convert from delta to wye. Do not lift the common neutral connections inside the motor and rewire for delta, because the voltages will be wrong.
Please answer question
Show digram 3 phase motor 110 and 220
Star (or wye) connection is where each of the three phases has a fourth conductor, neutral, as its current return. Current flow in this configuration is phase to neutral, which is also grounded back at the distribution center. There will be five total connections, phase A, B, and C, neutral, and (protective earth) ground. Delta connection is where each of the three phases uses the prior phase as its current return. Current flow in this configuration is phase to phase, and there is no neutral, though there is still a ground. There will be four total connections, phase A, B, and C, and (protective earth) ground.
If it is a 240 v delta motor it needs a 240 v three-phase supply, which has 139 v between line and neutral, so 440 v would not be acceptable.
An open delta connection is a delta connection with one phase removed, but still supplied with three line conductors. An open wye is a wye connection with one phase removed, supplying a three line conductors and a neutral conductor. An open-delta/open-wye is a method of providing a reduced-load three-phase supply using just two single-phase transformers, rather than the preferred method of using three single-phase transformers.
A star connection is where the three phase nonpolarities are tied to a single point, and very often grounded. A delta connection is where the nonpolarity of one phase is tied to the polarity of another phase, forming a greek delta shape. If measuring from polarity to nonpolarity on a single phase, in the star formation you are looking at L-N voltages; in the delta connection, you are looking at L-L voltages (L-N voltages * square root of three).
Star and delta connection
Show digram 3 phase motor 110 and 220
when starting a 3 phase induction motor,first start with star connection,because reduced current is being applied and after start change it to delta connection then. full line current is applied to the motor.
normally delta connection wired in 3 phase induction motor. during starting wiring is in Star and after running normal speed changeover to delta .beacause starting time its phase voltage equals less root3 times of line voltage ,line current and phase current equals. in Delta phase voltage and line voltage equals, and phase current equals root3 times line current
In star connection when two phase is short,it work as single phase system. In delta when one phase is open ,it work as a single phase.
Star (or wye) connection is where each of the three phases has a fourth conductor, neutral, as its current return. Current flow in this configuration is phase to neutral, which is also grounded back at the distribution center. There will be five total connections, phase A, B, and C, neutral, and (protective earth) ground. Delta connection is where each of the three phases uses the prior phase as its current return. Current flow in this configuration is phase to phase, and there is no neutral, though there is still a ground. There will be four total connections, phase A, B, and C, and (protective earth) ground.
Using star delta method of wiring you can run high rated motor with out any high starting current. Star connection can provide 3 phase power as well as single phase load
Google star delta motor connections. If a motor is wired in star-delta (Yd), it starts up with lots of torque and then switches over to delta for normal "running". This is because the start-up current per phase when delta connected is much larger than star.
An open delta connection is a delta connection with one phase removed, but still supplied with three line conductors. An open wye is a wye connection with one phase removed, supplying a three line conductors and a neutral conductor. An open-delta/open-wye is a method of providing a reduced-load three-phase supply using just two single-phase transformers, rather than the preferred method of using three single-phase transformers.
If it is a 240 v delta motor it needs a 240 v three-phase supply, which has 139 v between line and neutral, so 440 v would not be acceptable.
A star connection is where the three phase nonpolarities are tied to a single point, and very often grounded. A delta connection is where the nonpolarity of one phase is tied to the polarity of another phase, forming a greek delta shape. If measuring from polarity to nonpolarity on a single phase, in the star formation you are looking at L-N voltages; in the delta connection, you are looking at L-L voltages (L-N voltages * square root of three).
why three phase induction motor is delta connected