0
In a series circuit, the current does not change. It is simple the total voltage divided by the total impedence. However, in a parallel circuit the current splits. More current will go down the path with less impedence, and vice versa. For example, you have two parallel branches, 1 and 2, with resistances R1 and R2 respectively. Also, the total current flowing is I, while the current down each branch is I1 and I2.
I1= I(R2)/(R1+R2)
I2= I(R1)/(R1+R2)
Also note that I1 + I2 = I.
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
What is a seiries circuit?
Series CircuitWe say Resistances are in series if the same current flows through all Resistances. A circuit containing of only series resistances is called a series circuit. A series circuit is a circuit that has the same intensity of current flow through its elements.
What is a rule for current flowing round a circuit?
In a series circuit, the current at every point in the circuit is the same. This is a consequence of Kirchoff's Current Law, which states that the signed sum of the currents entering a node must equal zero. Since a series circuit consists of nodes with only two elements connected to each node, it follows that the current at every point in a series circuit is the same.
Why is the current in a series circuit the same all way round?
The number of electrons coming out of the positive end of the loop must be the same as the number of electrons going into the negative end. If it isn't, then electrons had to be created, or destroyed, or were injected, or leaked out, somewhere along the series loop.
Is voltage measured in series?
ANSWER:Imagine that all the elements of a simple circuit (such as a battery, a light globe , a switch, and a resistor ) When the switch is closed , the electric current flows round and round the circuit just the same way as water would flow through these elements if the circuit had a Water pressure supply and a thin section of pipe and then a thick section of pipe etc . The FLOW of the electricity in Amps can be thought of as the same thing as the Flow rate of water in a pipe system. The Ammeter, is put into the circuit between any 2elements of the circuit, so that the current flows through it , as well as all the other elements (parts) of the circuit. When current flows through the various elements the flow rate (Current) is the same in all of them. As the current flows through, there is a drop of pressure (Voltage) as the electrons flow through each of the elements of the circuit. The actual pressure(volts) in each piece of the circuit , can be measured, by placing a Voltmeter across any individual item in the circuit. The drop in pressure at each item is measured by connecting each terminal of a Voltmeter across the item you are dealing with. The voltage across the 2terminals of the supply will be perhaps 12 Volt(a car battery) The volts ' pressure ' across the globe may be say 8 volt and the volts across the switch may be 3volts and the volts across the resistor may be only 1 volt. Always think of Ampere, as 'Flow Rate', and think of Voltage as ' Electric Pressure' If a circuit has a spot where it splits into 2 separate circuits , and then turns back into 1 piece of circuit, the current flowing as it goes into the 2 different passages, is split up, or shared between the 2 passages, and then the 2 separate currents join together again as they re-enter the single part of the circuit. To find out the current flow in each of the 2 parallel parts of the circuit you must place the Ammeter in series within each of the 2peices of circuit . The 2 separate curent readings will have a total equal to the current reading in the main single passage circuit.
Will the lightbulb be brighter in series circuit or brighter in a parallel circuit?
This question is the wrong way round. Assuming you the light bulbs are identical, they are brighter when connected to the power source in parallel than in series. This is because each bulb uses the entire potential difference of the power source, whereas in series, the bulbs act as potential dividers, reducing the voltage across the others and therefore the current passing through all of them.
What is the significance of resonance in electrical and electronics circuits?
circuits go round
How is a series circuit constructed?
A series circuit is a simple circuit, a circuit that simply goes round in a loop without any branches off. Often, these circuits have just a battery, an appliance and a switch. A lamp is an example of one of these.
What is the duration of In the Round TV series?
The duration of In the Round - TV series - is 1800.0 seconds.
Is it true that when a round bulb and a long are connected in a parallel circuit the long bulb is brighter than the round bulb?
Bulbs that are connected in parallel would be the same brightness as a bulb on its own. If the bulbs were in series with other bulbs, then they would be dimmer. The voltage would drop across a series.
When did In the Round - TV series - end?
In the Round - TV series - ended on 1970-06-28.
When was In the Round - TV series - created?
In the Round - TV series - was created on 1970-04-19.
When was Gather 'Round - TV series - created?
Gather 'Round - TV series - was created in 1978.
Why aren't all parallels on the earth the same length?
Because they are parallel, while the earth is round. So a line round the equator will be longer than a line parallel with it at a higher latitude.
What is a seiries circuit?
Series CircuitWe say Resistances are in series if the same current flows through all Resistances. A circuit containing of only series resistances is called a series circuit. A series circuit is a circuit that has the same intensity of current flow through its elements.
What keeps temperatures on the pacific coast relatively moderate year round?
Ocean Currents
In baseball what is the first round playoff series?
division series
Line of longitude arent parallel to each other why?
they aren't because the earth is round deerrhh!
