0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
Car stalls when put in gear?
if its a manual then it could be three things, clutch cable or throttle cable, or IAC (idle air control valve) but if its an automatic it could be throttle cable or IAC.
How to Install a throttle cable for a 1985 dodge power wagon?
remove the bad cable and put the good one! ;-)
What could be wrong with a 1999 Chevy Camaro RS V6 with throttle response problems?
i would check for slack in the cable wire if so get tie strapes and pull the slack hold it and put strapes around it enough so it wont go back in (throttle cable)
How do you put a throttle cable bracket with a auto kick down on a holley?
Holley sells the necessary hardware.
What is making your 2004 jeep Cherokee accelerate without you pressing on the gas?
The throttle position sensor is more than likely, misaligned and needs to be put back into spec. Otherwise check to see if something is binding up your throttle cable some where between the gas peal, and the throttle body (located in the engine bay.)
What causes an accelerator to stick to the floor and can this be repaired?
could be a sticky cable. I would go to your local parts store and get some powder graphite. Put some on each end of the cable and work the cable back and forth. If it is just sticky this should help. If it is a frayed cable it must be replaced. could also be a sticky throttle assembly, but I would start with the cable.
How do you fit a speedo cable to Renault clio?
on a clio 172 ph2 (facelift )its not a cable its a sensor its on the gearbox just below the power-steering bottle it will cost you £25.35 On a clio 172 ph1 ( prefaclift) there is a cable, take off inner wing/plastic arch, peel back the sound guard. Once this is done disconnect the cable at both ends.. Next, at the bulk head pull the cable free, thread the new cable in and connect to accelerator and then to the throttle body, put on clip to hold the cable in place... put back sound deading and inner wing, all done..
Why is your 1976 Suzuki 125 revving up when you crank it?
Your throttle cable is probably dirty and stuck up, or the cylinder in the carburetor, which holds the carb needle, is stuck in the open throttle position (UP)- this could be due to a long overdue cleaning and maintenance routine. It is also ONE OF THE MOST DANGEROUS THINGS TO HAPPEN TO A MOTORCYCLE RUNNING AT FULL SPEED: a STUCK THROTTLE. The best remedy for this situation is to check both cable and carb. You will have to unscrew the top of the carb where the throttle cable enters the carburetor barrel. Pull the cable out and check if the spring still works. If the spring is still original (1976) it WILL most probably be broken and won't return the cylinder DOWN to the closed throttle position. Replace the spring. If it is still whole, shiny, and good- spray it with Carb Cleaner. Actuate your throttle by twisting the grip- check the return action on the spring. If it goes back, your cable is good. If not, put the small red hose that comes with your Carb Cleaner spray into the spray nozzle and spray a little INTO the cable's housing to clean the cable. Twist the throttle grip while the cleaner is still wet to get the cleaner into the cable. If this loosens the cable, then your problem is found. Spray a bit more cleaner into the cable, (best done if you REMOVE THE WHOLE CABLE AND SPRAY INTO IT FROM BOTH ENDS AND PULL THE CABLE IN AND OUT). Then spray WHITE SILICON LUBRICANT into the cable from both ends. Assemble your carb and cable. Start your engine as you normally would. If all else fails, replace the throttle cable.
How do you change a throttle cable diagram Yamaha pw80?
take the old one off than put the new one on simple as that.
How do you find idle control valve in a 1997 Mitsubishi eclipse 2.4 L?
The idle air control valve can be found under the throttle body. In order to get to it: 1. Disconnect negative battery cable. 2. Remove air intake from throttle body. 3. Disconnect throttle body cable. 4. Disconnect sensor connectors from IAC valve, and throttle position sensor. 5. Remove 4 bolts from throttle body using 10mm socket wrench. 6. Take throttle body, turn bottom side up, remove 4 mounting screws from IAC Once you do that you have removed the IAC. Reverse the steps to put it back on starting at number 6 and working your way back to number one
What is causing long shifts in your 1997 grand Cherokee tranny?
clutchs in tranny are going bad, bye a new or remanufactured tranny to put in it, it is better than haveing it rebuilt It could also be the spring on the throttle valve being broken or installed in corectly. It is mounted on the side of trans. follow the cable from throttle body to transmission the spring should pull on the lever away from throttle body. ot he cable is not ajusted properly. look for ajustments for the tv "throttle valve"cable.
How do you adjust idle on 1998 BMW R1200C?
The idle/throttle adjustment is located at the proximal (inside) aspect of the right hand grip. To see it you have slide back the rubber boot that fits over the throttle cable- just peel it back and expose the adjustment nut. Start bike, put in neutral, set kick stand--- turn nut clock/counterclockwise to the desired setting.
