How do you Remove and Replace the IAC valve on a 2000 Taurus?

Remove the wiring harness from your 2000 Dodge Stratus EGR valve. Remove the EGR valve retaining screws. Reverse the process to install the new EGR valve.

if it is a dohc engine then you may have to remove the intake manifold

There is one intake valve for each cylinder. It is located in the top of the head. If you remove the valve cover, you can see the stem of the valves by peeking through the caps in the valve spring. If you want to replace a valve, it will be necessary to first remove the cylinder head.

It is located underneath the throttle body.

Look on you tube they have a video of doing this job

First you have to pop the hood, then look for the EGR valve. Once it is located, remove it and replace it with the new one. When finished, close the hood and you're good to go.

You have to remove the entire caliper and brake rotor and punch out the old stud and press in a new one.

remove right valve cover on cadilac sts

you have to remove the pan and wen the pan is removed you have to remove the valve body then pop out the connector to the solenoid the unbolt the 4 bolts andf it is loose

# The EGR valve is bolted to the rear cylinder head,at the transaxle end # Remove the air intake duct from the throttle body and air filter housing # Detach the vacuum line from the EGR valve.Disconnect the EGR pipe nut # Remove the EGR valve mounting fasteners # Remove the EGR valve and gasket from the manifold.Discard the gasket

How can I replace the headlamp on a 2000 Saturn SL1

The thermostat should have a air bleed valve built in and the air bleed valve should be facing straight up.

IF YOU MEAN THE OIL IS DOWN IN THE SPARK PLUG TUBE. THERE IS A SEAL THAT IS IN THE VALVE COVER THAT GOES AROUND THE TOP OF THE SPARK PLUG TUBE, THEY GET HARD AND START TO LEAK INTO THE TUBES AFTER A WHILE. YOU WILL HAVE TO REMOVE THE VALVE COVER TO REPLACE THEM.

On the 2.8 it's on top of the plenum at the back. disconnect the hose & unscrew the pcv valve & replace.

No. 2000 Taurus and Sable are the only interchange.

To replace brake pads and rotor: Unbolt wheel, unbolt caliper, remove caliper, unbolt caliper bracket, remove rotor, replace rotor, bolt up bracket, compress caliper, replace pads, replace caliper, bolt up caliper, bolt up wheel, repeat whole thing on other side...

That is a huge job. You have to remove the transmission before you can remove the flywheel. The main seal is under the flywheel/flexplate. Rick Visit my auto blog at http://free-auto-repair-advice.blogspot.com

There are screws that hold it on. Sometimes they are located under the compartment.

I am very sorry. I was under the impression that if I go to the address bar and ask a question. The answer would be right forecoming. I only asked how to replace the heater core on a 2000 ford taurus. And received only run-arounds.

2000 SE what year do you have, and do you have a 3.0 liter 12 valve engine, or a 3.0 liter 24 valve DOHC engine? 12 valve

It's under the throttle body. To get to it, you'll need to remove the throttle body and flip it upside down. The IAC valve is mounted by two screws to the throttle body, and it has a gasket that you will need to replace if you remove the IAC valve, so make sure you have a new gasket on hand if you intend to take off the IAC valve.

how to remove and replace hood ornament cdaillac deville 2004

Look to the rear of the driverside valve cover. You will see if at this entry point. Remove the hose and simply pull it out and replace it with the new one.

There are 8 bolts that hold it on. First remove the cover to the coil packs, Then the coil packs then the vallve cover,

It may be a EGR valve issue. This valve is normally closed at idle and opens at about 40mph.