Chevy Corvette
Chevy Impala
Chevy Tahoe
Ford Expedition XLT

How do you Remove door window 1982 corvette?

001

Top Answer
User Avatar
Wiki User
Answered
2014-10-06 21:36:31
2014-10-06 21:36:31

Remove the inside door panel of your 1982 Chevy Corvette. Remove the window retaining clips. The window will lift out.

001
๐ŸŽƒ
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0
User Avatar

Related Questions


remove the window to get access to the nuts remove them then the mirrors look in the pillars an tighten them up.


The power window travel for a 77 Corvette is adjusted by bolts that are in slotted holes. Remove the door panel. Make small adjustments to each adjustment slot until the window travels properly.


Remove inside door handle and window crank handle, remove inside door panel, remove vent window and channel assembly, remove window.


First you will need to gain access to the parts holding the door handle in place. To do so, you'll need to remove the inside door panel, with the window up. From there, you'll be able to access the door handle.


To remove the drivers side window and regulator, you will need to remove the door panel from the door. Then you can unbolt the regulator and window to remove them.


First remove the Window Crank Handle. Then remove all of the screws you can find, 1 for the door release, 1 for the door grip, and 4 for the door panel. Pop loose all of the lower door area, and carefullyremove the door panel. Remove the plastic behid the door panel, SAVE IT!!. With the window all of the way down, remove the screws that hold the window in and remove the window. Revers to reinstall, being sure to locate the new window into the grooves for that.


To install a new window regulator on a MGRZ driver's door, remove the door panel and the wiring attached to the power window mechanism. Remove stereo speaker from the inside door and the window glass. Remove the old window regulator and replace with new.


First you need to remove the door panel.Then remove the door handle bracket.Peel back the moisture shield.Tape the window into place,then unbolt the window from the regulator.Remove the window regulator from the access hole in the door.



Window Adjustment 101 ---- Door Window Height Adjustment (Major)Door Window Height Adjustment (Minor)Door Window Tip-In AdjustmentBaseline SettingRemove door panel & water deflector.Remove door speaker assembly.Remove window door clamp sight access plugs.Position window to access clamp nuts.Disconnect window switch.Loosen window clamp nuts through door top opening.Regulator in full UP position.Loosely tighten rear window clamp nut.With helper, position window to door opening.Tighten window clamps to 89 lb/in.Open door and install window clamp access plugs.Install speaker, water deflector, door panel.Perform minor height and tip-in adjustments as necessary:Window fully UP.Remove large access plug (under front of door).Loosen window regulator front channel mounting nut.Remove reflector from door panel.Loosen jack screw jam nut.Adjust tip-in with jack screw (clockwise = outward).Tighten jack screw jam nut.Lower window.Tighten window regulator front channel mounting nut.Raise window, check alignment.Reinstall access plug & reflector.Door Window Height Adjustment (Minor)If window height is off less than 3mm. (0.12").Open door and remove both small access plugs (under door).Loosen regulator jack screw jam nuts (both).Adjust both jack screws equally.Close the door and check alignment.Reinstall access plugs.


First remove the door panel.Then remove the moisture barrier.Next remove the window motor from the window regulator.


you have to remove window crank and door handel first


You have to remove the door trim on the inside of the door. Also remove the window crank handle if it is manual windows. 1. remove the window regulator by unbolting the regulator from the door shell and sliding the window guide arms out of the window channels. 2. You then remove either side or both sides of the vertical window channel that the window goes up and down on. 3. Finally, most of the time you need to remove the window rubber seal that runs horizontally along the bottom of the window opening to get the glass and the regulator channel that is attached to the glass out of the door.


Remove the armrest, door handle, and window handle. You will need a special tool to get the window handle off. They're cheap and you can get them at any auto parts store. Remove the screws at the bottom of the door panel then CAREFULLY pull the retaining clips out of the door by sliding a screwdriver between the panel and door where the clips are (you'll find them at the front and back) it is VERY easy to tear the backing of the door panel when removing them, so be careful and patient. Slide the door panel up to unhook the top of it from the door. Remove the window regulator bolts and carefully slide the rollers out of the window tracks. Carefully remove the window from the top of the door. slide the window regulator out.


the inner door panel has to come off and the whole window unbolts and it will come out.


you have to remove the door panal off and its in the door,bottom of window.


The 1993 Chevrolet Corvette inside door panels are held in place with eight retaining clips and two retaining bolts. The retaining bolts will be near the door handle. Remove the retaining bolts and pry outward on the retaining clips.


You will need to remove the door panel of your 1997 Chevrolet Corvette. When the door panel is removed the mirror retaining bolts will be visible. Tighten the mirror retaining bolts.


To remove the door panel on the Holden Astra, first pop off the light lens if the door has a light in the door. Then unhook the light from connector. Remove the screws holding on the armrest, door handle, and window crank if equipped.


remove plastic moulding around door handle and door lock. unscrew door handle and unsnap plastic anchors around lower portion of door unscrew door panel from door. lift up on panel and remove. remove plastic. unscrew motor from door , let window down and remove two screws holding window. remove motor and metal bar replace and reverse process. 1991 Nissan maxima


Here are complete step-by-step instructions (with photos) on how to remove a door panel:http://www.ricksfreeautorepairadvice.com/repair-topics/window-power-repair/remove-a-door-panel-from-any-vehicle-without-a-diagram


i usually use a sawsawll. or a table saw.


You have to remove the door panel and anything else like door pulls and window handles.


How do you remove the drivers door panel and fix the window. It fell off the track.


lower window to down position(if you can) remove door panel remove window weather stripping remove black window surround (should be a screw on top of surround towards back edge) then stationary window should unbolt then remove pins that hold operator to track pick up and pull out the operating window reveverse putting in



Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.