answersLogoWhite

0


Best Answer

The starter is located underneath the driver seat. There are 3 bolts on the rear one on the front and a nut ion the top of the starter that keeps it in place. I would recommend getting a manual from your auto parts store. They can help answer your simple questions like this

User Avatar

Wiki User

โˆ™ 2007-12-20 05:31:05
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar

Add your answer:

Earn +20 pts
Q: How do you access starter motor on a automatic Toyota Previa?
Write your answer...
Submit
Related questions

Where is the jack stored in a 1991 Toyota Previa?

Jack location for Toyota PreviaToyota Previa jack and tire iron are located under front passenger seat. Access from front on door side. It is held down with a butterfly screw and/or rubber retaining band. Easy to get out.this is on most united state previa,most European made previa the jack are locate under the driver seat.


Where may a person read consumer reviews for the Toyota Previa?

There are many great places to read consumer reviews for the Toyota Previa. The online resources are the easiest to access. Check out "Kelly Blue Book", "Consumer Reports", and "Consumer Guide".


How do you take out EGR valve out of Previa 1991?

disconnect battery, disconnect the starter, disconnect the starter mount bracket from the engine and you can access the egr valve no need to lower the engine good luck


Where does one check the oil level on a 1992 Toyota Previa?

Engine oil dipstick is accessed under the drivers seat. Release the seat, tilt back, pull up the access cover. The engine oil dipstick is there along with the Automatic Transmission dipstick (if it applies). Vehicle should be on level ground.


Where is starter location on Toyota sequoia?

Under the intake manifold Between the top intake manifold and the engine block. The top intake manifold must be removed to access the starter.


Where is the starter located on a 1999 Toyota Four Runner?

The starter is located on the passenger side of the motor rignt under the manifold. You can access it from underneath, or remove the right tire, and you can get to it as well.


How do you get back cover off to replace brake light on Toyota Previa 1998 automatic?

If it's the brake light in the boot lid then you have to take the cover off the inside of the boot lid and then you will have access to the light bulbs. If it's the brake light in the rear quarter panel then you open boot lid and unscrew the two bolts holding the light cluster and slide it backwards, then you will have access to the bulbs


Where is the temperature sender or temperature sensor on a 1995 Toyota Previa?

There are three temperature sensors on a 95 Previa engine. They are located on the left front side of the engine. The lower one is somwhat accessable from under the vehicle but access to the other two will require removal of the passenger seat and the access cover under the seat. A Haynes manual is the best way to go about getting info.


How do you replace starter on 2002 Toyota tunder?

The starter is located under the intake manifold. You will have to remove the intake manifold being very careful not to drop any of the bolts into an in port. The starter is fairly easy to access once the manifold is off.


Where is the fuel filter on a Toyota Hi-ace 2000 SBV?

under the fuel injection unit you may need to remove the starter to access it


How do you replace a 1998 Toyota forerunner starter?

Disconnect the battery first. Then there are 2 bolts holding the starter to the transmission case. Take those off. Then slide the motor out so you can get to the connections on it. Remove these and carefully remove the starter. Reverse the order to reinstall. Some things that help. Remove the wheel and place the car on a stand so you have good access. Then there is a panel to keep debris out of the engine and give you access to the starter. Remove this also.


Do you have to drop the engine to change the spark pluges on a 95 Toyota Previa?

No. Remove the passenger seat, remove the cosmetic panel under the passenger door, peel of the carpet and unbolt the access cover. Younow can see the engine head where your spark plugs are.


Which bolts do you remove when taking out the seat to get to the spark plug access cover on a 1994 Toyota Previa?

24 bolts and screws in all. 4 seat bolts, two on the seat support panel, 3 rocker panel screws, one seat belt, about 14 under the carpet, and holding the metal access cover.


Where is the starter on a 2000 GMC Jimmy?

The starter is on the right side of the engine. The right tire needs to be removed to access the starter.


Where is the location of th starter on a Saturn sw2?

the starter is located in the back of the engine. you have to get under the vehicle in order to access the starter.


Where is the starter located on a 1999 Cadillac Eldorado?

The starter is under the intake manifold. You must remove the intake to access the starter.


Where is the starter motor on a Toyota lucida?

You'll find the starter motor for your Toyota Lucida mounted behind the engine oil filler which is accessed by pulling up the yellow seat release and tipping the passenger seat back to reveal the service access panel that lies below a removable section of carpet. A point to note is that access to the starter motor is very tight and can take some time to remove if the fixing bolts are tight. The good news is that you only need a 14 mm, a 12 mm spanner and a cross head screw driver to remove it.


How do you get to the starter on a 1995 Mazda 626?

You must remove the airbox assembly to access the starter from above


How do you replace the starter on an 1989 Toyota pick up truck?

On the V6 engine the bottom bolt is accessible from under the truck easily but not the top one. You can remove the right front tire and wheel and access it.


Where is the starter in a 1998 Saturn SL2?

starter is located on the firewall side of the engine. Access is easiest from underneath the car


Where is starter solenoid in 2000 ford focus and how do you access it?

on the starter , which is between the motor and the firewall. and under the intake man.


Where is the starter located on a 1997 Nissan Maxima?

the starter is located on the transmission side under the air intake box. You have to remove the intake assembly to access the starter.


Where is oil sending unit on dodge caravan?

on my 1990 with 3.0 L, behind starter. remove starter to access unit


Where is the Starter located on a 1992 Grand am 2 door automatic V6 and how you can replace it?

Look at the bottom rear of engine either left or right side--Follow + battery cable Disconnect - battery cable Lift and safely secure appropriate side of vehicle Remove mounting bolts (2) Slide starter out to access wires Disconnect wiring Remove starter REverse to install


How do change the starter on a 2000 Dodge Durango?

== # Disconnect and isolate the battery negative cable. # Raise and support the vehicle. # Remove the nut and the lock washer that secures the lower mounting flange of the starter motor to the stud on the automatic transmission torque converter housing # While supporting the starter motor with one hand, use the other hand to remove the screw and washer that secures the upper mounting flange of the starter motor to the automatic transmission torque converter housing. # Slide the automatic transmission cooler tube bracket forward on the tubes far enough for the starter motor mounting flange to be removed from the lower mounting stud. # Lower the starter motor from the front of the automatic transmission torque converter housing far enough to access and remove the nut that secures the battery positive cable eyelet terminal to the starter solenoid B(+) terminal stud. Always support the starter motor during this process. Do not let the starter motor hang from the wire harness. # Remove the battery positive cable eyelet terminal from the solenoid B(+) terminal stud. Always support the starter motor during this process. Do not let the starter motor hang from the wire harness. # Disconnect the battery positive cable solenoid terminal wire harness connector from the connector receptacle on the starter solenoid. Always support the starter motor during this process. Do not let the starter motor hang from the wire harness. # Remove the starter motor from the automatic transmission torque converter housing. == # Disconnect and isolate the battery negative cable. # Raise and support the vehicle. # Remove the screw and washer (rearward facing) that secures the lower mounting flange of the starter motor to the automatic transmission torque converter housing # While supporting the starter motor with one hand, use the other hand to remove the screw and washer (rearward facing) that secures the upper mounting flange of the starter motor to the automatic transmission torque converter housing. # Lower the starter motor from the front of the automatic transmission torque converter housing far enough to access and remove the nut that secures the battery positive cable eyelet terminal to the starter solenoid B(+) terminal stud. Always support the starter motor during this process. Do not let the starter motor hang from the wire harness. # Remove the battery positive cable eyelet terminal from the solenoid B(+) terminal stud. Always support the starter motor during this process. Do not let the starter motor hang from the wire harness. # Disconnect the battery positive cable solenoid terminal wire harness connector from the connector receptacle on the starter solenoid. Always support the starter motor during this process. Do not let the starter motor hang from the wire harness. # Remove the starter motor from the automatic transmission torque converter housing. == == # Position the starter motor to the automatic transmission torque converter housing. # Reconnect the battery positive cable solenoid terminal wire harness connector to the connector receptacle on the starter solenoid. Always support the starter motor during this process. Do not let the starter motor hang from the wire harness. # Install the battery positive cable eyelet terminal onto the solenoid B(+) terminal stud. Always support the starter motor during this process. Do not let the starter motor hang from the wire harness. # Install and tighten the nut that secures the battery positive cable eyelet terminal to the starter solenoid B(+) terminal stud. Tighten the nut to 13.6 N·m (120 in. lbs.) Always support the starter motor during this process. Do not let the starter motor hang from the wire harness. # Position the hole in the starter motor lower mounting flange over the stud on the automatic transmission torque converter housing. # Slide the automatic transmission cooler tube bracket rearward on the tubes and into position over the starter motor upper mounting flange. # Loosely install the screw and washer unit that secures the starter motor upper mounting flange to the automatic transmission torque converter housing. # Loosely install the lock washer and nut that secures the starter motor lower mounting flange to the stud on the automatic transmission torque converter housing. # Tighten the screw and washer unit and the nut that secure the starter motor mounting flange to the automatic transmission torque converter housing. Tighten the screw and the nut to 67.8 N·m (50 ft. lbs.) # Lower the vehicle. # Reconnect the battery negative cable. == # Position the starter motor to the automatic transmission torque converter housing. # Reconnect the battery positive cable solenoid terminal wire harness connector to the connector receptacle on the starter solenoid. Always support the starter motor during this process. Do not let the starter motor hang from the wire harness. # Install the battery positive cable eyelet terminal onto the solenoid B(+) terminal stud. Always support the starter motor during this process. Do not let the starter motor hang from the wire harness. # Install and tighten the nut that secures the battery positive cable eyelet terminal to the starter solenoid B(+) terminal stud. Tighten the nut to 13.6 N·m (120 in. lbs.) Always support the starter motor during this process. Do not let the starter motor hang from the wire harness. # Position the starter motor mounting flange on the automatic transmission torque converter housing and loosely install the two screw and washer units to secure it. # Tighten the two screw and washer units that secure the starter motor mounting flange to the automatic transmission torque converter housing. Tighten the screws to 67.8 N·m (50 ft. lbs.) # Lower the vehicle. # Reconnect the battery negative cable.