0
How do you access the antenna assembly on a 2002 Mitsubishi Montero?
Wiki User
∙ 17y agoWant this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
How to remove the fuel pump in a 1995 Mitsubishi montero?
You must remove the fuel tank to gain access to the fuel pump.
Where is the fuel pump located and how do you remove it on a 1998 mitsubishi montero support?
Mounted on top and inside the fuel tank. Look for an access panel above the fuel pump. If there is none you must remove the fuel tank in order to gain access to the pump.
How do you replace the power antenna on a 1997 Mitsubishi 3000gt?
To access the power antenna you have to remove the storage container next the spare tire. then remove the screws holding the plastic piece in place. Pry back the plastic trim and you will see the antenna behind it. On the outside there is a cross shaped piece holding the antenna in place. find something such as pliers to unscrew it (counter-clockwise). the antenna will fall out as a complete unit.
How do you access the left front marker bulb on a 2000 Mitsubishi Montero Sport?
In the front wheel well there are platic screw latches that hold wheel well coul in place. Remove the front ones to gain access to side marker light compartment.
Where are Mitsubishi Montero signal and bake fuses?
The owner's manual will tell you the exact location. They may be on the driver's side, just to the left of the steering column underneath. Or under the hood on the right. They are to access and inexpensive to replace.
How do you change antenna motor on 2002 sequoia?
I believe you have to take off the Wheel Well liner and access to access the antenna.
How do you remove the headlights on a 2001 Mitsubishi Montero Sport?
I have a 2000 and just spent an hour so I thought I would share. You need to take off the plastic grill piece to access the retaining pins - the retaining screw on top of the front and then I had to remove the blinker assembly to get the 2 retaining screws there. One those are off, there are 2 screws and one spring.
How do you take off the horn cover on a Mitsubishi Montero?
On my 2000 montero sport, the horn is behind the driver side on the bottom plastic griill below the bumper. From the front take out three screws for access. Reach behind with box end wrench to unbolt the horn and remove. It's elcetric plug has latch to remove.
Where is the oil pan to drain the oil on a Mitsubishi 2002 montero sport?
you have to take off skid plate first to access oil drain plug, and to also get at oil filter. Make sure you dont drain transmission by mistake.
How do you access the antenna on a 2000 VW Beetle?
Pull the headliner and access in the middle of the car behind the sunroof. Or if you want just the antenna, not the cable-to-the-antenna, stand outside the car and unscrew it. very carefully
Where is the antenna mast assembly located on a 2002 Mitsubishi Montero?
The antenna motor is located in the right front fender. Access to the motor is via the right front wheel well: remove the front right tire first, then several plastic pop-out fasteners and a few sheet metal screws holding the plastic wheel well cover in place (you can just push it aside, as it's fairly flexible). Two more screws hold the motor in place. If your antenna isn't moving up or down, chances are the mast itself is broken, not the power motor. If it is, you will need to remove the broken peice from inside the motor assembly ( a few screws on the motor will allow you to open it). Once done, put it all back together, turn the radio on and put the new mast in place (in the up position). Now turn the radio off and it should retract; if it doesn't, repeat after turning the mast toothed spline (should be facing toward the vehicle front).
How do you take the rotor off of a Mitsubishi Montero Sport?
To access the rotor, remove the tire and brake caliper. There will be a cap protecting the bolt that holds the rotor onto the spindle. Removing the cap, located in the center of the rotor (on the spindle, not the rotor itself) will allow you to get access to the bolt. Removing that bolt frees the rotor from the spindle.
