answersLogoWhite

0


Best Answer

If the engine does not start: (1) rotate the carburetor main jet needle valve clockwise (close) until it touches its stopping point - DO NOT FORCE OR GO BEYOND THE POINT OF TOUCHING as it may damage the tip. (2) Rotate the needle valve counter-clockwise (open) 1-1/4 to 1-1/2 turns - this should be close enough to start the engine. Start the engine and let it warm up about five minutes. (3) Rotate the needle valve clockwise (close) slowly until the engine starts to stall for lack of fuel, then rotate the needle valve counter-clockwise (open) slowly until the engine starts to stall from flooding (too much fuel). (4) Set the needle valve to a midpoint between the two extremes for the best "purr" of the engine. If the engine "sputters" when a load is added, open the needle valve an extra 1/8 turn for a slightly richer mixture. If the engine starts and you just want to adjust the carburetor, step (1) is not necessary.

User Avatar

Wiki User

14y ago
This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: How do you adjust the carburetor on a 6.0HP Briggs and Stratton lawn mower engine?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Related questions

How do you adjust the carburetor on a 17.5 Briggs and stratton?

My engine is idling too high. How do I adjust the idle speed?


How do you adjust the carburetor on a Briggs and stratton 18 horsepower vangaurd v twin engine?

with a big freagin hammer


How do you adjust the carburetor on a lawnmower engine?

Go to your local autoparts store and by the rebuild kit according to your carburetor. Inside the box will be an exploded diagram of the carb which will make it relativly simple to rebuild First of all what kind of engine do you have. Briggs and Stratton or Tecumseh. If you have a Briggs & Stratton engine the factory setting on the little black screw is 1 turn out, Tecumseh engines 'usually' do not have adjustments. hope this helps


Why does your Briggs and Stratton L head twin spit gas out of the carburetor and flood out at starting?

A Briggs and Stratton L head twin engine wills pit gas out of the carburetor and flood out when starting if the diaphragm has been damaged. This will cause excessive fuel to enter the carburetor.


Where can you get a carburetor for a lawn tractor Murray model 425001x8A?

It is a Briggs & Stratton Engine, so get the engine model and try jackssmallengines.com.


How do you adjust valves on 17Hp Briggs and stratton ohv Family ybsxs.5012VP 274826?

You can adjust the valves on your 17 horsepower Briggs and Stratton engine by turning the adjustment screws. The adjustments screws will determine how much fuel goes into the piston chamber.


How do you adjust valves on a 19.5 Briggs and Stratton Its a 2006 or 2007 engine?

Try watching the video in the link below.


How does the gas system work on a 3.5 Briggs and Stratton engine?

The fuel system on a Briggs and Stratton engine works by fuel being gravity feed from the fuel tank. Fuel goes to the carburetor where air and gas the mix, after the air and fuel mix it is feed into the engine where the engine goes through the four strokes.


Where is the fuel filter located on a Honda self propelled push mower with a Briggs and Stratton engine?

The fuel filter for a Honda self propelled push mower with a Briggs and Stratton engine is located between the fuel tank and the carburetor. The fuel filter is only about one inch long.


How do you adjust timing on your 17.5 Briggs and stratton lawnmower engine?

There is no way to adjust the timing on a 17.5 Briggs engine. The magnet is on the side of the flywheel and there is only one way the flywheel can line up. All you can do is make wure that the coil is gapped correctly.


Why does your Briggs and stratton quantum xm 4 hp engine start but not keep running?

Clean out the carburetor with gas, the reason it wont keep running is its not getting enough gas through the carburetor.


Why does Briggs and stratton 3.5 engine only stay started when starting fluid is sprayed in the carburetor?

Because your carburetor is not getting fuel to the engine - could be a plug in the fuel line or it could be dirt in the screen in the pick up tube in the carburetor. I would suggest you clean the carbutator.