0
Just replace the switch, it is as simple as that: the wiring is the same. It is the switch that is different. So simply TURN OFF the power AT THE BREAKER BOX and replace the switch. <><><>
As always, if you are in doubt about what to do, the best advice anyone should give you is to call a licensed electrician to advise what work is needed.
Before you do any work yourself,
on electrical circuits, equipment or appliances,
always use a test meter to ensure the circuit is, in fact, de-energized.
IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOB
SAFELY AND COMPETENTLY
REFER THIS WORK TO QUALIFIED PROFESSIONALS.
What else can I help you with?
How do you convert a swivel recessed light to accept the pendant light kit?
To convert a swivel recessed light to accept a pendant light kit, you will need to remove the existing recessed light fixture and install a pendant light fixture in its place. This typically involves disconnecting the wiring for the recessed light and attaching it to the pendant light fixture according to the manufacturer's instructions. You may also need to install a mounting bracket to support the pendant light fixture.
What is a vapor tight incandesent recessed light fixture?
A vapor-tight incandescent recessed light fixture is a sealed lighting fixture that prevents moisture, dust, and other particles from entering the fixture, making it suitable for use in damp or wet locations. It is designed to protect the light source and electrical components from potential damage caused by environmental factors.
Can a 130 flood light go into a 120 volt recessed light fixture?
yes <<>> There might be a problem. It depends on what the wattage of the flood light is. If the wattage is higher than what the fixture is rated for then it is not a good idea to use it. Look inside of the recessed fixture and look for the label that was put there by the manufacturer. It will state what the maximum wattage the fixture can legally handle.
Do recessed light kits come with the trim?
Yes. Recessed lights consist of two parts, the trim and the housing. The housing is the light fixture that is installed in the ceiling, and the trim is the light itself.
Can you convert an existing flush mount ceiling light into a recessed light?
Sure. Get a recessed light that is designed to be installed in "old Work". You must hav eenough room in ceiling to contain the recessed light. There may be some issues in some locations where the recessed fixture may overheat if for instance there is insulation around the fixture. Light should have an over temp cutoff. There should be a template with recessed light and a built in box to wire in the power from the old light. If you carefully cut out the sheetrock in ceiling according to the template dimensions, you will be able to use the piece you remove to repair the hole should there be no room for the recessed light. If there is attic access where the new light will be installed, you may be able to use a "new Work" light fixture since you can mount it from above. Go to someplace like Home Depot or Lowes and see what they have available.
How can I change a recessed light to a pendant light?
To change a recessed light to a pendant light, you will need to remove the recessed light fixture, install a pendant light fixture in its place, and connect the wiring according to the pendant light's instructions.
How can I convert a square recessed light to a different style using a square recessed light conversion kit?
To convert a square recessed light to a different style using a square recessed light conversion kit, follow these steps: Turn off the power to the light fixture at the circuit breaker. Remove the existing square recessed light trim and bulb. Install the conversion kit according to the manufacturer's instructions. Attach the new light fixture or trim to the conversion kit. Turn the power back on and test the new light fixture. Make sure to follow all safety precautions and consult a professional if needed.
How can I use a can light adapter to convert a recessed light fixture into a pendant light fixture?
To convert a recessed light fixture into a pendant light fixture using a can light adapter, you will need to remove the existing recessed light trim and bulb, then install the can light adapter into the recessed housing. Next, attach the pendant light fixture to the adapter according to the manufacturer's instructions. Finally, adjust the pendant light height and secure it in place to complete the conversion.
How do I change a recessed light bulb?
To change a recessed light bulb, first turn off the power to the light fixture. Then, carefully remove the trim and the bulb. Replace the old bulb with a new one of the same type and wattage. Finally, reattach the trim and restore power to the fixture.
How do you convert a swivel recessed light to accept the pendant light kit?
To convert a swivel recessed light to accept a pendant light kit, you will need to remove the existing recessed light fixture and install a pendant light fixture in its place. This typically involves disconnecting the wiring for the recessed light and attaching it to the pendant light fixture according to the manufacturer's instructions. You may also need to install a mounting bracket to support the pendant light fixture.
How can I convert a recessed light into a pendant light?
To convert a recessed light into a pendant light, you will need to remove the recessed light fixture and install a pendant light fixture in its place. This typically involves disconnecting the wiring of the recessed light and connecting the wiring of the pendant light. You may also need to install a mounting bracket or canopy to support the pendant light.
How can I remove a recessed light can?
To remove a recessed light can, first turn off the power to the light fixture. Then, remove the light bulb and trim from the fixture. Next, unscrew the screws holding the fixture in place and carefully pull the can out of the ceiling. Disconnect the wires and remove the can from the ceiling.
What is a vapor tight incandesent recessed light fixture?
A vapor-tight incandescent recessed light fixture is a sealed lighting fixture that prevents moisture, dust, and other particles from entering the fixture, making it suitable for use in damp or wet locations. It is designed to protect the light source and electrical components from potential damage caused by environmental factors.
How can I replace a recessed light with a pendant light?
To replace a recessed light with a pendant light, you will need to remove the recessed light fixture, install a pendant light fixture in its place, and connect the wiring following the pendant light's instructions. It's important to turn off the power before starting and consult a professional if you're unsure about the process.
How can I replace recessed lighting in my home?
To replace recessed lighting in your home, first turn off the power to the lights at the circuit breaker. Remove the old light fixture by unscrewing it from the ceiling. Disconnect the wires and remove the fixture. Install the new recessed light fixture by following the manufacturer's instructions. Connect the wires, secure the fixture in place, and turn the power back on to test the new light.
What is a another word for recessed light?
Recessed light can be called as down light, pot light (canadian), can light (for canister in American). It is a light fixture that installed in hollow opening in ceiling.
How can I remove a recessed light fixture?
To remove a recessed light fixture, first turn off the power to the fixture at the circuit breaker. Then, carefully remove the trim and light bulb. Next, unscrew the screws holding the fixture in place and disconnect the wires. Finally, carefully pull the fixture out of the ceiling. Be sure to follow all safety precautions and consult a professional if needed.
