0
Most cars and trucks today have what is called a serpentine belt which runs most accessories.They are very dependable and usually easy to replace. To decide if your belt needs replacing, simply look at the grooved side of the belt to see if it is cracking badly. A couple of cracks every 3 inches is normal, but if you see cracks every 1-2 inches I would recommend that you replace it. On most cars and trucks the procedure is basically the same. First off, get the correct belt by bringing your cars VIN number to the parts store(located on your cars dashboard) the parts store may need it. If there are two choices, get them both so you can complete the repair. Once you have the correct belt, take a minute to review how the belt runs across the pulleys and also check to see if your car/ truck has a underhood diagram of belt routing in case you need it. In most cases you will need a socket wrench or breaker bar with either a 3/8" and /or 1/2" head on it and possibly a short extension. Some models may require a wrench of these similar sizes.Now that you are ready to go to work, you will need to find the spring loaded tensioner which is generally located near the top of the belt path; it usually has a shinny pulley on it. Look at the tensioner and insert the tool into it and apply opposing pressure to release the belt.Now, simply install the new belt making sure it fits into the grooves on all the pulleys. Start the car to check it and you are done and you saved yourelf some money!
Wiki User
∙ 12y ago
Add your answer:
Earn +20 pts
What is a tensioner on your 98 olds intrigue?
A spring loaded pully that keeps the serpentine belt tight
Need copy of diagram to replace serpentine belt on 1998 Olds 88?
I found this information with a diagram of the serpentine belt. Hope it helps.
How do you replace the serpentine belt on a 98 Olds Intrigue?
TAke a wrench and put on the tensoiner and take the tension off of the belt and slip it off. Then thread the new one on as per the schematic on the fan shroud. If it isn't there. draw one before you take it off. Don't rely on memory.
How do you route a serpentine belt on Olds Cierra 1992?
How do you route a serpentine belt on a 1992 Cierra Oldsmobile
A serpentine belt routing diagram for 1999 olds Intrigue 3.5 engine where can you get one now?
My husband and my brother in law need a diagram so they can get my car done. please thank you
Where is a serpentine belt diagram for a 94 Oldsmobile 88?
My 1992 Olds Delta 88 has the serpentine belt diagram on the top of the radiator
Do you need to take the motor mounts loose to replace your serpentine belt on your olds 1998 88?
all u have to do is take it out and then put it back in
How do you replace a serpentine belt on an 97 Olds Achieva?
replacing achieva serpentine on a 96i have a 96 and you have to completely remove the motor mount and all of the bolts holding it on the engine to replace the belt,also carefully jack up the engine since it will fall on the ground if you take off the mount
I need the diagram for a 2001 3.5 liter olds aurora serpentine belt diagram?
i need diagrama for serpentine belt for 2000 aurora
What is the routing or diagram to install the serpentine belt on a 2002 Olds Intrigue and Which is the tensioner?
That info should be under the hood in the engine compartment, if not get a repair manual or use the internet to see if you can find the diagram that you need.
How do you change a serpentine belt on a 1997 olds 88?
push back on tensioner, then re move belt.
How do you get rid belt squeal on a 1999 olds intrigue?
You should not be getting belt squeal because it is a serpentine belt, and not a v-belt. The squealing is most likely a bad bearing in one of the pulleys. Whatever you do, do NOT use belt dressing on a serpentine belt, as this can cause more problems. I suggest you remove the belt, and turn each pulley by hand and listen for the squealing. Some, you may not be able to turn though, such as the crank pulley. They should turn smoothly, with no noise, or intermittent resistance.
