0
Follow the below steps to replace the camshaft sensor 2003 stratus:
1) Loosen the two bolts securing the air inlet resonator, the large plastic component that the air filter outlet tube connects to, using a ratchet and socket. Now, pull the air filter outlet tube from the air filter housing.
2) Pull the oil separator tube from the air filter outlet tube using a slight twisting motion. Remove the air filter outlet tube and resonator from the engine compartment, exposing the camshaft position sensor.
3) Unplug the camshaft position sensor's wiring harness. Remove the screws securing the camshaft position sensor using a ratchet and socket.
4) Remove the screw securing the camshaft magnet to the camshaft using a ratchet and Allen-bit
socket. Then, pull the magnet from the end of the camshaft.
5) Line up the dowel pins on the new camshaft magnet, which comes with the new camshaft position sensor, with the locating holes on the end of the camshaft; then, place the camshaft sensor back onto the cylinder head in the same position it was in prior to removal.
6) Press the air filter outlet tube onto the outlet on the air filter box, then tighten the hose clamp to between 20 and 30 inch-pounds.
Guide the resonator's hose onto the inlet on the throttle body and tighten the hose clamp to between 20 and 30 inch-pounds.
7) Set the resonator in place on top of the engine, aligning its bolt holes with those on top of the engine.
Wiki User
∙ 11y ago
Add your answer:
Earn +20 pts
Where is the camshaft position sensor on a 2002 dodge stratus with a 2.7 liter?
It attaches to the timing chain cover on the front(pass side) of the engine. It is the three wire sensor above the serpentine belts.
Where is the camshaft sensor located on a 2001 Dodge Stratus V-6 2.7 liter?
It is on the front of the engine. It aims at the left cam sprocket through the timing cover.
Where is the camshaft position sensor on a 4.6L?
The camshaft position sensor on a 4.6 liter engine is positioned on the side of the motor on the front of the cylinder head. A 4.6 liter engine has a camshaft position sensor on each cylinder head.
Where is the camshaft sensor on a 2006 dodge ram 5.7 liter?
where is the camshaft sensor on a 2006 dodge ram 5.7 litre
Where is the camshaft position sensor on a 2.2 Sunfire?
The Pontiac 2.2 liter engine camshaft position sensor can be found on the back of each cylinder head. The camshaft position sensor should be labeled as such.
Camshaft position sensor location on a ford 6.0 powerstroke?
The camshaft position sensor, on a Ford 6.0 liter power stroke engine, is located inside of the rear engine cover. The sensor is on the back of the camshaft.
Where is the camshaft sensor on a 2001 8.1 liter motor?
It is behind the starter.
Where is the camshaft position sensor located on a 1999 Chevy truck 1500 4.3 liter fwd?
The camshaft position sensor is a part of the distributer. There are 2 electrical plugs going to it, 1 is for the coil,the other is for the Camshaft sensor.
Where is the camshaft sensor on a 98 gmc k2500 5.7 liter engine?
In the distributor
Where is the camshaft position sensor located on a 1999 ranger 4.0 v-6?
Where is the camshaft position sensor located on a 1999 ford ranger 4.0 liter engine
Where is the camshaft sensor on a 1996 4 liter grand Cherokee?
The cam sensor is inside the distributor under the rotor.
Where is the camshaft position sensor located on a 2002 GMC savanna 5.7 liter motor?
the sensor is underneath the distributor cap
