0
How do you change the fuel filter on a 2002 Chevrolet Cavalier How do you relieve the pressure off the fuel line to replace the filter Is there a fuse that must be removed?
Rocsam
i donot think u have to releave pressure i believe u just remove the filter some gas will come out but do not be alarmed email me at s2j26s@cs.com Begin by removing the fuel pump fuse from the fuse panel. It should be a blue 15amp fuse. The fuse panel is inside your car, to the left of the steering column. Once removed, start the engine. After the engine fails to start (i.e. it stalls on you) don't worry, it just means there is no fuel going to the engine, so the engine is going to die. Attempt starting the car at least three more times and if the car doesn't start, then the fuel pressure has been released successfully. Make sure you turn the ignition to the OFF position before continuing.
Wiki User
∙ 15y ago
Add your answer:
Earn +20 pts
How do you relieve fuel pressure on 95 S10 2.2l?
To relieve the fuel pressure on a Chevrolet S10, the fuel pump relay should first be removed. Then, the engine should be startedand run until it stalls.
How do you remove headrest 99 Chevrolet Cavalier?
To remove the headrest in the 1999 Chevrolet Cavalier, first pull the headrest all the way up. You can then push down on the seat back around the base of the headrest. You will find two springs that can be removed with a pair of pliers. Once the springs are removed, just pull up on the headrest.
Is the ac line under pressure and if so how do you relieve it to replace the compressor?
Yes the ac lines are under pressure. The high side is under dangerously high pressure. The Freon needs to be removed by a reclaiming machine and the pressure will be removed.
How much fluid might be extracted during a paracentesis to relieve pressure?
If pressure relief is an additional goal, many quarts may be removed.
How do you repair headlight switch in Chevrolet cavaliers?
The headlight switch is not repairable in a Cavalier. The switch will need to be removed and replaced. The procedure is different, depending on the Cavaliers year.
Is fuel pump access under back seat or under car on 1997 Chevrolet Cavalier?
No, the fuel tank must be removed to access the fuel pump.
How do you remove the door panel on a 1994 Chevrolet Cavalier Z24?
The door panel in a 1994 Chevrolet Cavalier Z24, can be removed by first removing the lens covers from any lights in the door. Then, remove the light sockets themselves with a screwdriver. Using a flat screwdriver, gently pop the clips on all sides of the door panel and remove it.
In a pool what is the white circle thing in the deep end?
This is the hydrostatic valve. If the pool is emptied it is removed to relieve water pressure caused by the surrounding water table If not removed a pool can float out of the ground.
How do you replace the starter on a 1991 Chevrolet Cavalier?
Replacing the starter on a 1991 Chevrolet Cavalier can be difficult for someone who has never worked on cars. The car first needs to be jacked up so that the starter can be reached. Then the wires will need to be taken off the starter and labeled so that they can be placed back on the new starter. The start will then then be taken off by removing the bolts. After the bolts are removed, the starter can be taken off and replaced.
How do you get the aluminum cover on top of the engine of a 99 Chevrolet Cavalier Z24 so you can change your spark plugs you removed the 4 bolts but it still feels like something is holding it back?
there is the spark plug boots
Where is Gear shift light on Chevrolet Cavalier 2000?
The Chevrolet Cavalier 200's gear shift light bulb is found by the N in the gear shift near the driver's side. To access it, two bolts must be removed underneath the arm rest, one under the cup by the shift, and one more under the rubber insert in the tray. Lift the console, and follow the wire to access the light itself.
How do you change the power steering pump reservoir on a2004 Chevy cavalier?
There are two bolts, two brackets, and a pressure hose which have to be removed in order to separate the power steering pump and the reservoir. The bolts are removed with a 13mm box end wrench, the brackets (top and bottom)of the reservoir are removed by using a flat head screwdriver to pry them loose. The pressure hose is removed by using pliers to decompress the ring clip around the end of the hose.
