Chevy S-10

How do you change the plug wires on a Chevy S-10 4 cylinder?

828384

Top Answer
User Avatar
Wiki User
2015-07-15 21:03:59
2015-07-15 21:03:59

Changing plug wires is a fairly straight forward operation. If you can plug in a blender, you can change plug wires. The only thing to keep in mind, is to remove one wire at a time. Choose a wire to start with and remove it. Measure the old wire with the new set and try to match it with the wire that is closest in length to the wire you removed. place the new wire back on the terminals the same way the old one was. Make sure it seats on there and doesn't easily pop off. Repeat this process three more times and your done. Have fun! Chris

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

They should be on the side of the cylinder head. they will have plug wires ging to them.

User Avatar

The 1988 Chevy Cavalier spark plug wires are quite easy to remove. The spark plug wires simply pull off on each end. Put the new spark light wires on by pushing downward on each end.

User Avatar

change only one wires at a time,matching each to length.

User Avatar

What are the Best plug wires for 1997 Chevy truck? Today most plug wires are made using the same material. Just get wires for your vehicle model, mostly because they are cut to length.

User Avatar

i would change the spark plug wires

User Avatar

Change one at a time to avoid mixing up the firing order.

User Avatar

you can look in a haynes repair manual for it or contact your dealer

User Avatar

it is located to the right of the coils and plug wires on top of engine. facing it! it is a round cylinder shape. with wires to it on the top of it.

User Avatar

a bad coil or plug to be safe change both

User Avatar

It is a misfire code for # 5 cylinder. Check to make sure plug wires are on tight to all plugs. Consult manual to figure out #5 cylinder probably change that plug at least

User Avatar

Answer3 and 4 wires won't come under the air intake Take the plug wire off and use a spark plug wrench to take the plug out. Do this one at a time so you won't mix the wires up. Once you put the new plug in, replace the plug wire.

User Avatar

change plug wires on 1998 isuzu hombre 2.2

User Avatar

There is no distributor cap, only a ciol pack that the plug wires go to

User Avatar

Are you referring to spark plug wires

User Avatar

+ goes to starter solenoid, - goes to distributor side post. center plug wire goes to center plug on distributor.

User Avatar

Count the spark plug wires that are located under the black plastic resonator box. There are small aluminum heat sinks located on top of the spark plug harnesses, count them.

User Avatar

If it has 4 spark plugs, then it's a 4 CYLINDER. ............4 plug wires, then it's a 4 CYLINDER

User Avatar

How does the wires from the spark plug go to the rotor, which order?

User Avatar

No. the plug wires are made different and the spark plugs ae NOT the correct heat range.

User Avatar

The 2004 Trailblazer does not have plug wires. It has a coil pack per cylinder that connects direct to the spark plugs.

User Avatar

1 is where the rotor is when number 1 cylinder is firing. Then clockwise from 1, 8,4,3,6,5,7,2.

User Avatar

The spark plug wires on your 1994 Chevrolet Caprice are quite easy to change. The spark plug wires simply lift off on each end. Put the new spark plug wires on and push until you feel a click.

User Avatar

Changing the spark plug wires is very simple. The replacement wires are the Bosch 5812-07098319 set for the V6 orรŠBosch 5812-07098498 for the 4-cylinder. One at a time, disconnect the wire from the distributor and the plug. Replace with the wire that is the same length. ProceedรŠ

User Avatar

Electrical... try plug wires

User Avatar

plug all wires together.


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.