Ford Escort

How do you change the slave cylinder on a 1991 ford escort?

345

Top Answer
User Avatar
Wiki User
2009-06-21 12:50:54
2009-06-21 12:50:54

It is not too difficult. a lot easier than the clutch master cylinder; it is located on the lower front driver side of the engine; it is fed by the clutch master cylinder which is fed by the brake master cylinder; follow the lines and you will see it. You will need a flare nut wrench to disconnect the line. Then it simply unbolts fom the engine. Replace with new part, reconnect line, and bleed the air out. There is a bleeder fitting on the slave cylinder. Make sure to get all the air out of the line to prevent a weak pedal that could cause difficulty in shifting gears.

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

How do you change a slave cylinder on a 1995 Mazda B2300 2wd?

User Avatar

On the passanger side bellhousing.

User Avatar

You will have to remove the transmission since the slave cylinder on the 91 yj is inside the bellhousing.

User Avatar

Inside bell housing. Transmission has to be removed to gain access to the slave cylinder/throw-out bearing.

User Avatar

the slave cylinder is the easiest position compared to the master cylinder...1991 S10 4.3...

User Avatar

BAD clutch slave cylinder, wore out clutch and pressure plate.

User Avatar

I'm pretty sure that on that vehicle the slave cylinder is located inside the transmssion which means the transmission must be removed to replace it

User Avatar

According to one of Fords websites : For a 1991 Ford Escort : 1.9 liter four cylinder engine ( the spark plugs are gapped at .054 inch ) 1.8 ( .044 inch )

User Avatar

According to my Chilton's Auto Repair Manual : A 1991 Ford Escort , 1.9 liter four cylinder engine takes : ( 4.0 U.S. quarts with engine oil filter change )

User Avatar

bleed it the same way u bleed the brakes

User Avatar

Check your clutch master cylinder and slave cylinder for leaks,if no leaks,then you need a new clutch kit.

User Avatar

I am paying $195 parts and labor in my 98 maxima

User Avatar

YES - according to www . motorcraft . com ( no spaces ) It shows for the 1991 Ford Escort / EXP - 1.9 L ( 116 cubic inch ) 4 cylinder PCV valve - Motorcraft part # - EV 157

User Avatar

I was looking at one of the Ford websites and it shows for the automatic transaxle ( transmission ) used with the 1.9 litre four cylinder engine in a 1991 Ford Escort : ( yes , Motorcraft FT-123 filter inside the transaxle pan )

User Avatar

- buy new wires for a 4 cylinder - remove 1 wire, check against new wires, matching size = use that one- repeat 3 times

User Avatar

no it is hydraulic.dont know what your problem is but check clutch master cylinder and slave cylinder operation,if ok may just be a bad clutch

User Avatar

It is notadjustable, You either have a bad clutch slave cylinder, clutch master cylinder. The clutch and pressure plate may just be worn out.

User Avatar

It is the same as almost all 4 cylinder engines. 1-3-4-2.

User Avatar

I use a "C" clamp but a big set of channel lock pliers works good too.

User Avatar

"How to set timing on 1991 ford escort lx 1.9?"

User Avatar

How do you enable anti theft alarm on 1991 ford escort lx

User Avatar

There is no adjustment on that year. You either have a worn out clutch disc or a bad clutch slave cylinder. Could be a bad clutch master cylinder too.

User Avatar

13,I think- I drive an escort


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.