0
It is nearly impossible to get at from the underside of the hood.
It is a pop-in fitting, with wings that spread out one it pops into place.
Your best bet is to slide something under the head of the nozzle, something thin like a credit card or a store card, simultanously from the left and right side and try to squeeze the wings that hold it in place so that you can pop it out from the top side of the hood.
Once you succeed, you should pull out a bit of the hose and then you can pull the nozzle out of the hose. Press the new nozzle into the hose, and pop the nozzle back in place.
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
How do you change the windshield washer nozzle on a Toyota Sienna?
Found an easy way to do it from outside the car, that worked great. Grabbed what remained of the nozzle with some pliers and crushed it. That left the base in the hole, and I was able to use a small screw driver to release the clips from the top of the hood and pull it up out of the top of the hood with the hose still attached. Pulled off the hose from the old nozzle, and put the new one on the hose. Snapped the new nozzle into the hole and Voila!. Took less than 5 minutes this way!
What is the tank that is located under the battery on 2004 Toyota Sienna?
The tank that is located under the battery on a 2004 Toyota Sienna is a windshield washer fluid tank. Toyota put this tank in this position on the 2004 to 2010 models of the Sienna.
How do you refill windshield washer to Toyota Sienna 1998?
The washer reservoir is located behind the passenger side head light, It is a white plastic container with a black cap, that has the washer symbol on it like the one on the steering wheel stalk.
How do you replace a windshield washer nozzle on a 1998 F-150?
On the inside of the hood disconnect the washer hose from the nozzle, and squeeze the plastic under it together. Then push it up it should come out pretty easy.
How do you Replace the washer nozzle on a jaguar X-Type?
If you are looking to replace the washer nozzle cover (the painted part) all you have to do is carefully pull out the nozzle with a pair of needle-nose pliers and hold onto it while installing the new plate. You should be able to let go of the nozzle after installed the new plate and it will retract itself into the bumper.
Will a pressure washer remove chipped paint from metal?
Yes it will with small nozzle.
How do replace washer nozzle on 2004 durango?
Simply disconnect the washer hose if not already broken and then squeeze the locking clips on the upper and lower side of the nozzle and then pull straight out the top. Clean the area and snap the new part in and connect the hose after removing the broken old part of the nozzle.
How do you change windshield washer pump in 1990 Toyota Camry?
I have the same problem except I can't even find it, do you know how to access or location of the washer pump?
Picture of Honda CR-V rear window washer nozzle?
A picture of a Honda CRV rear window washer nozzle can be obtained from most Honda dealerships. The picture can also be found at most auto-parts stores.
How do you replace washer pump on 2009 Toyota Camry?
how to replace the washer pump on a 2009 toyota camry
How do you replace the windshield washer reservoir on sienna?
To replace the window washer reservoir, you must first locate the reservoir under the hood, usually along the side fender area. (You can follow the rubber hose that is attached to the spray nozzle down to your reservoir). Now detach the two wires connected to the little pump motor inside the reservoir, and any bolts securing the reservoir to your car. You may need to look for the bolts. Take your time, figure out how the thing is secured, and get er out of there. If the thing is buried, you may have to remove another part to get to the reservoir. If this is the case, take your time (maybe take a picture), keep track of your nuts and bolts, and keep with it. Good Luck
How do you replace a windshield washer nozzle on a 2003 Saturn Vue?
It is very easy ... Open the hood ... there is a long cover over the washer fluid tubing that connects to the nozzle .. so you have to take this cover off ... separate nozzel from tube . Insert new nozzle from outside of car . connect to tubing .. replace panel/cover and you are done !!!
