1. Hold the Water Pump sprocket in position using the aperture
in the front cover.
2. Remove:
a. Upper Timing Cover
b. Manifold Heat Shield
c. Oxygen Sensor Wiring Harness Plug
d. Auxiliary Belt
3. Release water pump drain plug and drain.
4. Disconnect wiring harness plug from temperature sensor
and remove water hose from thermostat housing and heater
hose from the radiator.
5. Remove from water pump.
6. Remove the water pump service hatch.
7. Attach the Water pump holding tool (Laser Tools do one, as do Snap-on)with two of the service cover bolts in the outer slotted holes.
8. Secure the tool to the water pump sprocket using the 3
internal bolts.
9. Tighten to ensure tool is fitted securely.
10. Remove the bolts holding the Water Pump to the sprocket.
The engine timing is maintained as the timing chain is
securely fixed to the pump sprocket.
11. Remove the Water Pump.
12. Replace the Water Pump, refit the bolts retaining the pump
to the sprocket and remove the holding tool.
13. Re-assemble components in reverse order.
15 to 22 ft./lbs.
620,48 kJ
It is a Remington Model 12 .22 cal. pump
Pump It Up Fiesta was created on 2011-01-22.
Rossi
Winchester and Browning
How do I align the arrows on the gears for a oil pump on a 1992 toyota 22 RE engine? wsbahr@gmail.com
On a 1998 18i 16v Artic it's fuse #22
You can find that in the haynes manual at auto zone.Its kinda hard to find but have patience you will find it.
About 250 for an early savage 22 pump ranger, but dont bother looking for info, theres none on the web.
Water Pump Replacement (3.4L)Removal ProcedureDrain the cooling system. Refer to Cooling System Draining and Filling.Remove the drive belt shield bolt.Remove the drive belt shield.Loosen the water pump pulley bolts.Remove the drive belt. Refer to Drive Belt Replacement for the 3.4L engine.Remove the water pump pulley bolts.Remove the water pump pulley.Remove the water pump bolts.Remove the water pump (1).Remove the water pump gasket (2).Clean the water pump gasket mating surfaces.Installation ProcedureInstall the water pump gasket (2).Install the water pump (1). Notice: Refer to Fastener Notice in the Preface section.Install the water pump bolts. TightenTighten the bolts to 10 N·m (89 lb in).Install the water pump pulley.Install the water pump pulley bolts. TightenTighten the bolts to 25 N·m (18 lb ft).Install the drive belt. Refer to Drive Belt Replacement for the 3.4L engine.Install the drive belt shield.Install the drive belt shield bolt. TightenTighten the bolt to 10 N·m (89 lb in).Fill the cooling system. Refer to Cooling System Draining and Filling./////////////////////////////////////////////////////////////////////////////////////////////////Water Pump Replacement (3.8L)Removal ProcedureDrain the cooling system. Refer to Cooling System Draining and Filling .Loosen the water pump pulley bolts.Remove the drive belt. Refer to Drive Belt Replacement in Engine Mechanical - 3.8L.Remove the water pump pulley bolts.Remove the water pump pulley.Remove the power steering pump and reposition. refer to Power Steering Pump Replacement in Power Steering System.Remove the water pump bolts.Remove the water pump.Remove the water pump gasket.Clean and inspect the water pump mating surfaces.Installation ProcedureInstall the water pump gasket.Install the water pump.Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.Install the water pump bolts. Tighten• Tighten the long water pump bolts to 34 N·m (25 lb ft). • Tighten the short water pump bolts to 22 N·m (16 lb ft).Install the water pump pulley.Install the water pump pulley bolts. TightenTighten the bolts to 13 N·m (115 lb in).Install the power steering pump. Refer to Power Steering Pump Replacement in Power Steering System.Install the drive belt. Refer to Drive Belt Replacement in Engine Mechanical - 3.8L.Fill the cooling system. Refer to Cooling System Draining and Filling .
Not sure what a "22 cap" pump is. The magazine capacity of a Remington pump rifle will depend on which MODEL, and whether you are loading 22 LR, 22 Long, or 22 Short. The Model 121A holds 20 Shorts, 15 longs, or 14 Long Rifle cartridges. A model 12 would hold 15, 12, or 10.