0
What else can I help you with?
What can you do if your 1992 Delta 88 won't start and the code says to clean the key and wait 3 minutes but that didn't work and a new key does the same thing?
You might have to bypass the security system or replace it. GM used the Passkey I, II and III security systems.....bypass kits for these can be found on Ebay and some other car websites.
How do you bypass the passkey on a 1991 Cadillac Eldorado?
Ok, here you go. A) With an ohm meter, measure how many ohms between one side and the other of the "chip" in the ignition key (from the metal ridge in the middle of the black plastic on one side of the key to the other side). An electronics store or Radio Shack will probably measure the resistance of the key for you. B) on the bottom of the steering column, find the passkey wires (they are yellow) and they are quite small. MAKE SURE YOU DONT HAVE THE AIRBAG WIRES!!! C) cut these wires and install a resistor of matching resistance to what you just tested....i.e. if the key measures 5 ohms, go to Radio Shack or an electronics store and buy a pack of 5 ohm resistors, solder it in between the two cut wires. D) Just remember that any properly cut ignition key will now start and run the car, the passkey system is defeated. This also works to use for a remote starter system, so you dont need a spare key or "Passkey (or VATS) II module"
How do you clean a key that's has the Pass Key II?
your key for ignition is made for that specific computer in your car,i had to replace my whole steering column,the salvage yard told me the key coming with it would work..it didnt it kept telling me to clean the key,so i had to pop out the old ignition outa the old steering column and it started first time!
When was Philip Barton Key II born?
Philip Barton Key II was born in 1818.
When did Philip Barton Key II die?
Philip Barton Key II died in 1859.
What are the ratings and certificates for The Key - 2013 II?
The Key - 2013 II is rated/received certificates of: UK:U
What is the ii chord in the key of C major?
The ii chord in the key of C major is D minor.
Who made that song that goes thats the way im missing you boy thats the way our love will unfold?
Soul II soul
How do I remove the vats or passkey I or II on a 98 Chevy lumina?
It's a VATS system. If you know the value of the resistor you can cut the wires going to the lock cylinder and solder in a resistor of the correct value.
What are the release dates for Clean House Comes Clean - 2007 Homeowners from Hell II 4-2?
Clean House Comes Clean - 2007 Homeowners from Hell II 4-2 was released on: USA: 11 March 2009
Can you reset passkey II on a GM truck?
Passkey II can be reset based on the type of Truck you are looking at. You can usually reset it by the steps below. To determine if the passkey is your problem you need to know if the security light is flashing, solid, or out. Observe the Security indicator lamp in the instrument panel. Remove the key from the lock cylinder. - Security indicator should be Flashing when the door is open. - Security indicator should be Off when all the doors are closed. - If the Security indicator does not come On or go Off correctly, refer to the Content Theft Deterrent System diagnostic and repair information in the applicable Service Manual. With the Doors closed, place the key in the lock cylinder and turn to the Run position. Observe the Security indicator lamp. - Lamp is On and does not go Off however, the engine starts. This indicates that the Vehicle Theft Deterrent (Passlock) system detected a fault when the engine was running. - Lamp flashes On and Off. This indicates a problem has been detected by the Passlock(Passlock™) system and the engine may not start this key cycle, a current condition. If you determine that the Passlock is the issue, you need to do some web research on the "corrosion of the passlock system" GM had massive issueswith them and you may be able to get the answer there.
How do you take off the steering wheel of a 1995 Monte Carlo with airbag to get to the key and ignition switch with a passkey II keylock?
Diconect the battery under colum disconect fuse for air bag then yellow wire to air bag and remove airbag then steeing wheel your going to pull up the turn unit to get room to the switch it should be basic from there hope this helps
