0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
How do you apply bathroom grout correctly without it constantly being dragged out?
"Grout is the stuff you apply between tiles to seal them in place. Grout tiles once the adhesive has dried fully (24 to 36 hours later). The best grout is waterproof and mould-resistant; some come ready-mixed. Use a grout float - a rubber-faced tool with foam backing - for large areas. Spread the grout across the tiles at right angles to the joins. Use a damp sponge to remove excess. Once the grout is dry, polish the surface with a dry cotton rag." I was taught by a contractor to apply and clean the grout diagonally.
What hand tool is used when applying grout?
A Float (it is a sponge with a firm side for pressing the grout into the spaces between the tiles) also several separate sponges and a lot of water.Note: If you are considering the newer style grout that is a "two part" mixing "epoxy style" of grout. Please work in very small areas and use a clean sponge to clean the areas. Buy a lot of sponges, way more than you would suspect. Although these products are very good they are difficult to work with.Good luck with your project.
Best way to replace grout?
The old grout can be cut out. The mist efficient way is with an oscillating tool with a grout blade. After the old grout is removed then new grout can be installed. This is a time consuming project.
How do you change tile grout color?
You can get grout stain. It will let you make it darker. If you want to change the grout altogether then it can be easily removed, but time consuming. Simple grout removal tools are available at local home stores. Also a oscillating multifunction power tool will make quick work of it. Then re-grout the joints in whatever color you choose. Grout charts are available where grout is sold. Remember grout will look darker when being installed and will dry lighter. Be very careful of making sure everything is clean. Vacuum out old joints with a wet/dry shop vac. If you use a power tool to remove grout have someone follow behind it with a shop vac. Or you will have dust everywhere.
Can I caulk over mold in my bathroom as a home improvement remedy?
Serious health problems can be caused my mold and mildew. You should repair damaged caulking between your bathroom shower tiles as soon as possible. You can use this tool grout spreader to clean your mess. You can purchase grout spreaders at any hardware or home improvement store.
What do i need besides tile to put down tile in a the kitchen?
You will need a clean , level cement surface, mortar, grout, tile spacers, notched trowel and wet tile saw. Also, a bucket and stirring tool.
What tool has a rubber edge used to clean mirrors?
squigi
Is there such a thing as grout remover?
Yes. You can remove grout around tiles by using a mechanical device that scrapes it away. The tool tip is usually made of tungsten carbide and has several teeth to gouge away the grout. You can either use a fairly cheap unpowered one or a more expensive one that uses power. You can also buy liquid grout remover for removal of grout residue.
How do you remove grout?
You can buy a little scraper tool that has a pointed or 'v'shaped end to clean the gap between the tiles without damaging them. after that its a matter of re-grouting. Make sure the area is dry first - rubbing alcohol works well.
What are some tools that start with the letter e?
An edger is used for concrete and grout work. An extension cord is a tool.
Is rubber mallet a synthetic rubber?
A rubber mallet is the name of a tool, and the rubber bit can be made out of several different materials, even certain plastics.
How do you grout tiles?
It is somewhat painstaking. There is a grout removal tool available at most big box hardware stores. It is basically a handsaw that uses hardened aggregate applied to the blade instead of teeth. You have to shave each joint down to a level below the surface that a new grout can be applied to and adhere (about 1/8" for non-sanded grout and 1/4" for sanded grout). If you are changing grout colors, you will want to use an acid (muriatic acid) to wash down the joint edges to remove any small amounts of the old grout at the surface edge that remain, prior to new grout installation. Because you are not installing the new grout to the full tile depth, it is advisable to use a latex additive to prevent cracking.
