0
just buy a slot which connect two these are used in primary and secondry schools
Wiki User
∙ 9y ago
Wiki User
∙ 9y agoSpeakers are output devices, so you would not normally connect them to an input. If you did connect a speaker to an input, it would behave like a microphone, only very weak and very bassy.
Add your answer:
Earn +20 pts
How do you connect on speaker in COMPUTER?
Find your sound card (The card with 3 or more different headphone jacks), and install the cord from the speakers into the 3.5mm Green Jack, or the one labeled Speakers.
Can you install subwoffers into a stock Saab 9-3?
Yes you can... if you still have a factory head unit then you will need what is called an RF modulator which you will connect to one of the speakers. This will give you the Av imputs for your amp.
Can you run a mixer through audio speakers?
In most cases you need 4 parts: 1- Input(microphone, iPod, CD player, radio, etc) 2- Mixer 3-amplifier 4- speakers
What is an audio video source selector?
A switcher that will connect 2-3-4 other devices such as a camera, vcr etc. one at a time to a single audio/video input on the TV set.
How do you connect numark mixdeck universal and 2 behringer speaker B415DSP and to your computer What also do you need?
1) mixer to speakers: Numark main XLR-output to Behringer speaker XLR-input 2) sound from computer: computer line out to a free input on the Numark 3) sound to computer: use the USB cable connector on the Numark (might also work the other way around, not 100% sure)
What is the rule when the input is 1 and the output is 5 and input is 5 and output is 1 and input is 9 and output is -3?
There are many possible answers. One of them is Output = 6 - Input.
How do you replace Chrysler lebaron dash speakers?
remove the grills connect two 3 1/2's (the left will fit VERY TIGHT) but it replaced cardboard and wired into pre made slots for the speakers very easy in the end.
How do you convert a 4 input NOR gate into multiple 2 input NOR gate?
you will need 2 two input AND gates to do this. connect the output of the first to one input of the second. you now have a three input AND gate. just remember when calculating timing that 2 inputs of the 3 have twice the gate delay of the remaining input, thus the output will have skew and possibly glitches. if timing is critical or glitching can't be tolerated it may be best to use an actual three input AND instead of kludging one.
PlayStation 3 can be connected with any tv?
That is correct only if the TV has at least RCA plugs. The PS3 does not connect to the TV by coaxial to the cable or antenna input
What is the flag input of AND gate?
To produce a 3-input OR gate when only 2-input OR gates are available: Use 3 OR gates Inputs to Gate A are input 1 and input 2 Input to Gate B is input 3 (if 2 inputs are necessary, include input...
How using two-input logic gates of your choice design a circuit to determine if two 3-bit numbers are the same or different?
Three 2-input XOR gates and one 3-input NOR gate will do the work. Connect each output of each XOR gate to one input of the 3-input NOR gate and apply the two 3-bit words to the inputs of the XOR gates. If X (X2X1X0) and Y(Y2Y1Y0) are two 3-bit words, X2 and Y2 will connect to one XOR gate, X1 and Y1 to the next XOR gate and X0 and Y0 to the last XOR gate. You could see the result of the operation on a LED connected to the output of the NOR gate. Other implementations are also possible of course. The solution above is absolutely correct, but includes a 3 input gate. If the task is to use only two input gates, then a small change will be needed. Take the outputs from any two XOR gates into a 2 input OR gate. Then take the output of the OR gate and the output of the third XOR gate into a 2 input NOR gate. The operation remains identical to the first solution but adheres to the brief of using gates with 2 inputs. In the real world, there is probably no reason to impose such a limitation on a design so the first solution would normally be the preferred route to take.
How do you connect your Dish receiver to your TV without input jacks?
Receivers can be connected to the TV via a Coaxial cable. This allows the TV to use Ch. 3-4, or Ch. 60 or 73 for TV2, to show a picture rather than the input.
