0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
How do you connect a 3 wire fixture to a 2 wire fixture that are connected to the same switch what do you connect the red wire to?
A three wire fixture most likely is one that has two separate loads within it. An example is a ceiling fan with a light fixture. If the three wire is used to separately switch the two loads you have to make a decision as to which load you want to work with the two wire fixture. Once that decision has been made connect the two wire fixture in parallel with the your selected load on the three wire fixture. On these types of installations the three wire fixture is usually controlled by two separate switches in a two gang box. The red and black wires of the three wire terminates on the bottom of either switch. The white wire is connected to the incoming neutral. The top of the switches are paralleled together with the "hot" feeder from the distribution source.
How do you repair a pull chain switch on a fluorescent light?
Shut off the breaker that supplies the voltage to the fluorescent fixture. Wire the new pull chain switch in series with the black incoming wire and the black wire of the ballast. Turn the breaker back on and your switch will now control the off on operation of the light fixture.
Were do you connect the dimmer wire?
There should be two wires coming from the dimmer switch unless it is a 3-way dimmer. The wires should be labled line and load on a normal 2-way switch. The line load is connected to the incoming power wire. the load wire is then connected to the wire that goes to the fixture. If you area replacing an old two way switch, then it will hook up exactly the same as the original switch, except for the fact that you will have to connect the pigtail wires of the switch to the other wires that used to be under screw terminals. I hope this answered your question. Thanks, Ben M. There should be two wires coming from the dimmer switch unless it is a 3-way dimmer. The wires should be labled line and load on a normal 2-way switch. The line load is connected to the incoming power wire. the load wire is then connected to the wire that goes to the fixture. If you area replacing an old two way switch, then it will hook up exactly the same as the original switch, except for the fact that you will have to connect the pigtail wires of the switch to the other wires that used to be under screw terminals. I hope this answered your question. Thanks, Ben M.
How do you connect a 240 v cooktop with 4 wires to a service panel with 3 wires?
The new cooktop has a 4 wire connection. Red & Black are hot. White is neutral, and green is ground. You existing panel is wired with 3 wires. Black & Red are hot and green is ground. There is no neutral wire. Connect the black to black, red to red, and then connect the white and ground together at the plug.
How do you wire a series of recessed lights to a single switch when the power goes to the lights first?
If you already know how to put one fixture on a 3-way, just connect white-to-white and black-to-black from one light to the next. If you're changing from a single switch to the 3-way, the exact wiring will depend on whether the power comes from the breaker box to the switch or the existing fixture. I'll assume you're starting from scratch or have the power going to the fixture. You need #15 two-wire with ground and #15 three-wire with ground romex. Run two-wire from the breaker box to the first light fixture. Pull a another two-wire from this box to switch A and a three-wire between the switches. String two-wire from the first light to the second, second to third, etc. In the first box, connect white from source to the white fixture wire and the white going to the second box; black from source to the black to switch A; and the black fixture wire to both the white to switch A and the black to the next fixture. At each of the other 5 fixtures, connect all white to white and black to black (three pair in each box except the last one). At switch A, connect the white from the fixture to the common (center) connector and the black directly to the black going to switch B. The red and white wires going to switch B are connected to the two outside connectors of switch A. At switch B, the black goes to the common connector and the red and white to the outside connectors. At each box, connect all the bare wires (second ground) to each other and to the fixture or box. Now turn the power back on. If all the connectors are tight, power should follow the black wires from source past the fixture and switch A to switch B. From there it will go through one or the other of the travellers and, if switch A is in the same position as B, up the white switch leg to the fixtures, turn on all the lights and go back to ground.
How do you connect a 3 wire fixture to a 2 wire fixture that are connected to the same switch what do you connect the red wire to?
A three wire fixture most likely is one that has two separate loads within it. An example is a ceiling fan with a light fixture. If the three wire is used to separately switch the two loads you have to make a decision as to which load you want to work with the two wire fixture. Once that decision has been made connect the two wire fixture in parallel with the your selected load on the three wire fixture. On these types of installations the three wire fixture is usually controlled by two separate switches in a two gang box. The red and black wires of the three wire terminates on the bottom of either switch. The white wire is connected to the incoming neutral. The top of the switches are paralleled together with the "hot" feeder from the distribution source.
Fluorescent Light Fixtures?
form_title= Fluorescent Light Fixtures form_header= Add light to your home with fluorescent light. How many fixtures do you need?*= {1, 2, 3, 4, 5, More than 5} Is the fixture for a drop ceiling?*= () Yes () No Do you want the fixtures delivered?*= () Yes () No
How do you repair a pull chain switch on a fluorescent light?
Shut off the breaker that supplies the voltage to the fluorescent fixture. Wire the new pull chain switch in series with the black incoming wire and the black wire of the ballast. Turn the breaker back on and your switch will now control the off on operation of the light fixture.
How did they use to wire two on off switches to one fixture?
You need two 3-way switches. To see a diagram use your favorite search engine and search for 3-way switch wiring. Each switch has a common connection point and two other terminals. Basically connect the "other" terminal on 1 switch to either "other" terminal on the second switch and then do it again for the remaining "other" terminal. Then connect the common on one switch to the fixture and the common on the remaining switch to supply voltage. Tie neutral and ground for fixture and supply to the white and bare wires respectively.
Were do you connect the dimmer wire?
There should be two wires coming from the dimmer switch unless it is a 3-way dimmer. The wires should be labled line and load on a normal 2-way switch. The line load is connected to the incoming power wire. the load wire is then connected to the wire that goes to the fixture. If you area replacing an old two way switch, then it will hook up exactly the same as the original switch, except for the fact that you will have to connect the pigtail wires of the switch to the other wires that used to be under screw terminals. I hope this answered your question. Thanks, Ben M. There should be two wires coming from the dimmer switch unless it is a 3-way dimmer. The wires should be labled line and load on a normal 2-way switch. The line load is connected to the incoming power wire. the load wire is then connected to the wire that goes to the fixture. If you area replacing an old two way switch, then it will hook up exactly the same as the original switch, except for the fact that you will have to connect the pigtail wires of the switch to the other wires that used to be under screw terminals. I hope this answered your question. Thanks, Ben M.
How do you direct wire security light from outlet have 3 wires?
A 3 wired electrical fixture includes positive, negative and ground. The ground can be attached to one of the screws in the wall. In the case of the other wires, matching the colors, twisting and capping the wires together will handle the electrical installation.
How hard is it to install a TiVo box for an electronics novice?
It is very easy to connect the boxes. There are only 3 wires to connect and it is well labeled as to where they go.
How do you connect a 240 v cooktop with 4 wires to a service panel with 3 wires?
The new cooktop has a 4 wire connection. Red & Black are hot. White is neutral, and green is ground. You existing panel is wired with 3 wires. Black & Red are hot and green is ground. There is no neutral wire. Connect the black to black, red to red, and then connect the white and ground together at the plug.
How do you wire a series of recessed lights to a single switch when the power goes to the lights first?
If you already know how to put one fixture on a 3-way, just connect white-to-white and black-to-black from one light to the next. If you're changing from a single switch to the 3-way, the exact wiring will depend on whether the power comes from the breaker box to the switch or the existing fixture. I'll assume you're starting from scratch or have the power going to the fixture. You need #15 two-wire with ground and #15 three-wire with ground romex. Run two-wire from the breaker box to the first light fixture. Pull a another two-wire from this box to switch A and a three-wire between the switches. String two-wire from the first light to the second, second to third, etc. In the first box, connect white from source to the white fixture wire and the white going to the second box; black from source to the black to switch A; and the black fixture wire to both the white to switch A and the black to the next fixture. At each of the other 5 fixtures, connect all white to white and black to black (three pair in each box except the last one). At switch A, connect the white from the fixture to the common (center) connector and the black directly to the black going to switch B. The red and white wires going to switch B are connected to the two outside connectors of switch A. At switch B, the black goes to the common connector and the red and white to the outside connectors. At each box, connect all the bare wires (second ground) to each other and to the fixture or box. Now turn the power back on. If all the connectors are tight, power should follow the black wires from source past the fixture and switch A to switch B. From there it will go through one or the other of the travellers and, if switch A is in the same position as B, up the white switch leg to the fixtures, turn on all the lights and go back to ground.
Which is the 3 gnition coil on a 2002 Hyundai sonata?
follow the spark plug wires from the engine and where they connect is your coils
How do you repair LDE8414ACE Maytag Dryer?
How do the wires connect on a 3 prong electrical cord on the lde8414ace maytag dryer
How do you connect HDMI to my DVD recorder?
Not all DVD recorders (DVRs) have an HDMI connection. If yours does not have one, then you cannot use an HDMI cable. You will have to use either Component (5 wires) or Composite (3 wires) cables to connect your DVR to your TV.
