0
There should be two wires coming from the dimmer switch unless it is a 3-way dimmer. The wires should be labled line and load on a normal 2-way switch. The line load is connected to the incoming power wire. the load wire is then connected to the wire that goes to the fixture. If you area replacing an old two way switch, then it will hook up exactly the same as the original switch, except for the fact that you will have to connect the pigtail wires of the switch to the other wires that used to be under screw terminals. I hope this answered your question. Thanks, Ben M. There should be two wires coming from the dimmer switch unless it is a 3-way dimmer. The wires should be labled line and load on a normal 2-way switch. The line load is connected to the incoming power wire. the load wire is then connected to the wire that goes to the fixture. If you area replacing an old two way switch, then it will hook up exactly the same as the original switch, except for the fact that you will have to connect the pigtail wires of the switch to the other wires that used to be under screw terminals. I hope this answered your question. Thanks, Ben M.
Wiki User
∙ 15y ago
Add your answer:
Earn +20 pts
How do you wire a 3-way dimmer switch that has two red wires and one black and one green when the box has two red and two black?
you can only have one dimmer, the other switch needs to be not a dimmer. the green wire is ground, it connects to a bare copper wire found in the box, or to the box itself, if the box is metal. the black wire is"common" it either connects to the wire found in the box that has power in it or to the black wire that goes to the light. the 2 red wires are"travelers" they connect to the wires found in the box that go from switch to switch. if you don't know how to check which wire does what( continuity), it is possible to keep changinging the connections until the switch works. you will want to do this with a conventional switch, and install the dimmer afer you identify what wires are travelers and wich are common. you will destroy a dimmer switch by searching for the right connection. once you have identified the common wires, it will be on the black screw of a 3way switch; you can put that wire on the black wire of the dimmer. one red goes on one traveler, the other on another traveler. there might be a white wire in the box, if it is connected to other white wires and not to the switch, leave it alone. if a single white wire is connected to old switch, it may be a traveler.you will connect a red dimmer wire to this. opening the other switch location will show you if the white wire is used as a traveler.the black wire has to be either power coming in, or the wire going to the light. the reds are just connecting the 2 switches.
How do you replace a dimmer light switch with a regular light switch coming off of a wall plug ive got 2 black wires 2 white wires 2 grounds and one red wire going to the light?
This is a relatively simple wiring job. Remember that all a switch is, is a means of interrupting the power coming from source (electrical panel) and travelling to load (light fixture). Without the switch, the light would stay on constantly. The black wire is a power wire and so is the red. The white wire is a neutral wire, and the green wire is the ground. You may have to do some trial and error to get it right as I can't see the actual wiring diagram you have. After shutting power off to that circuit, disconnect the dimmer switch and remove. Connect the two white wires together with a wire connector. Connect the two green wires. The red wire was probably part of the dimmer switch and should now be gone, but if it isn't then just cap it off. Now connect the black wire from the fixture to one of the terminals on the switch, and connect the black wire from the electrical panel to the remaining terminal on the switch. That's it.
How does a wire connect to a bulb?
You take a wire and stick it to the positive end of the batter. Then connect another wire to the negative end of the battery. Connect both wires to the lightbulb.
What color wire is the dimmer switch?
you can find it in alldata
How do you remove the generator from the motor?
you take the blue wire and connect it with the red then connect it to the yellow then you cut the green wire and there you go!
What wire does the illumination dimmer wire connect to?
12v switched source. such as headlight switch or dimmer on the dash.
What color wire do you connect to the dimmer wire from radio?
Don't connect the red wire or you will die.
Where do the orange wires connect on my stereo harness for a 92 regal?
orange wire is commonly the light/dimmer switch.
Where do you connect the orange wire in the car stereo?
I guess your talking about the dimmer it gets spliced into dash lights after switch.
What is the yellow wire with a black stripe for 2000 Mitsubishi galant for panel lights?
where does the yellow wire with a black stripe on it connect for dimmer lights,panel lights,and gear shift lights,for a 2000 Mitsubishi galant
Installing sunpro tachometer to 1990 Nissan sentra dimmer switch which wire does the white wire connect to from tachometer to dimmer switch?
ok. the first thing u do is unplug the ignition coil and find a red and black wire and just kinda skin it and touch it when the car is on to see any movement and the dimmer switch pull it out and find a green and blackwire hook the white wire up to that and test the lights you know turn the head lights on everything else is instructions when you buy the tach.
Can dimmers control switched receptacles intended for plug in lamps?
You can wire a dimmer into any circuit. The issue is where you do it for a specific outlet. The dimmer would just have to connect to a single outlet and not all outlets on the same circuit. The issue is getting a dimmer that is compatible with the device you are dimming. Some lighting requires special dimmers.
How do you wire a 3-way dimmer switch that has two red wires and one black and one green when the box has two red and two black?
you can only have one dimmer, the other switch needs to be not a dimmer. the green wire is ground, it connects to a bare copper wire found in the box, or to the box itself, if the box is metal. the black wire is"common" it either connects to the wire found in the box that has power in it or to the black wire that goes to the light. the 2 red wires are"travelers" they connect to the wires found in the box that go from switch to switch. if you don't know how to check which wire does what( continuity), it is possible to keep changinging the connections until the switch works. you will want to do this with a conventional switch, and install the dimmer afer you identify what wires are travelers and wich are common. you will destroy a dimmer switch by searching for the right connection. once you have identified the common wires, it will be on the black screw of a 3way switch; you can put that wire on the black wire of the dimmer. one red goes on one traveler, the other on another traveler. there might be a white wire in the box, if it is connected to other white wires and not to the switch, leave it alone. if a single white wire is connected to old switch, it may be a traveler.you will connect a red dimmer wire to this. opening the other switch location will show you if the white wire is used as a traveler.the black wire has to be either power coming in, or the wire going to the light. the reds are just connecting the 2 switches.
Where does the dimmer wire go on a after market radio?
It would go to the dimmer that controls the brightness of the dash lights.
How do you replace a dimmer light switch with a regular light switch coming off of a wall plug ive got 2 black wires 2 white wires 2 grounds and one red wire going to the light?
This is a relatively simple wiring job. Remember that all a switch is, is a means of interrupting the power coming from source (electrical panel) and travelling to load (light fixture). Without the switch, the light would stay on constantly. The black wire is a power wire and so is the red. The white wire is a neutral wire, and the green wire is the ground. You may have to do some trial and error to get it right as I can't see the actual wiring diagram you have. After shutting power off to that circuit, disconnect the dimmer switch and remove. Connect the two white wires together with a wire connector. Connect the two green wires. The red wire was probably part of the dimmer switch and should now be gone, but if it isn't then just cap it off. Now connect the black wire from the fixture to one of the terminals on the switch, and connect the black wire from the electrical panel to the remaining terminal on the switch. That's it.
How do you connect the wire from the alternator to the starter?
how do you connect the wire from the alternater to the starter?
How do you install a dimmer to a light installed with W wire B wire and ground W running into the switch box if the switch box has power from B wire W wire and ground?
If you have one wire into your switch box for your light. this is called a switch leg, the dimmer should be wired across the black and white wire wires.
