0
The lock valve is connected to a hydraulic cylinder by forcefully pressing it into the fitting and releasing the retaining ring. This will lock the cylinder into place and keep it from moving.
Wiki User
∙ 10y ago
Add your answer:
Earn +20 pts
How does air lock affect a hydrostatic test?
Air can cause a very unsafe rise in pressure as air can be compressed as opposed to water thus the rational for a T&P valve.
What is the purpose of the valve on a metal casket?
On the one hand to release inner pressure. On the other hand to give access to the lock (closing mechanism, usually operated by a crank), while still having a hermetically sealing (air and watertight) casket.
How do you pick or crack a masterlock?
Hit it hard with a hammer. Either the lock will break open, usually what happens, or you'll break whatever the lock is on.
What is the use of channel lock pliers?
Channel lock pliers are very versatile. My main use of them is for holding large and awkwardly sized objects, for instance, clearance trap nuts under sinks.
How can you get a skeleton key out of an antique door if it is stuck there?
First, if the key is only slightly jammed, wiggling and jiggling it might work it loose. However, I am assuming that if you are asking this question, the key must be good and jammed. If that is the case, the only way I know of is the following; however, it involves destroying the key and therefore, you should be prepared to obtain a new key from a locksmith. First, hopefully the door is unlocked, or open. If it is closed and locked, you will have to try the following. Remove the hinge pins from the door by tapping them out with a hammer and a centre punch, nail, or other pointed metal instrument. Once the hinge pins are out, try pulling the door away from the frame from the hinge side. You should then be able to remove the door from the frame even if the deadbolt is locked. (Note: This assumes you are on the side of the door where the hinge pins are visible. If not, you will have to access the other side of the door via a window into the room. Good luck!) Once you have gotten the door open by these means (if necessary), remove the doorknob, then the escutcheon plates (face plates with the keyhole in them). This will expose the hole drilled in the door for the keyhole, and the lock case itself. Now take a pair of locking pliers ("Vise Grips") and grab onto the shank of the key as close to the lock case as possible. Work the pliers back and forth until the key breaks off. Hopefully, the break will occur as close to the lock case as possible. Now, remove the screws from the edge of the door which hold the lock case in place. You should now be able to slide the lock case out of the door. Unscrew the cover from the lock assembly and extract the broken piece of key, being careful not to disturb any of the tumblers (levers), springs, etc. Good Luck!
What causes the brakes to suddenly lock up on a 1997 Lincoln Mark VIII?
May be the proportioning valve by the master cylinder
What is used to lock a valve spring on a valve?
A valve spring "keeper" or AKA a valve spring "retainer" is used to lock a valve spring to the valve.
Arms wont lift up or down on Bobcat 873?
this can be caused by a number of things * low oil level *damaged hydraulic pump *sticking or spool valve *worn valve body *damaged anticavity solenoid valve *damaged lift spool lock solenoid
Who invented the cylinder lock?
I think that Linus Yale Jr. was a lock manufacturer and patented the cylinder lock in 1861.
Have replaced the lock cylinder on a 1979 camaro and it still won't return to the lock position?
Then the rods that connect to it must be messed up, lubricate everything inside the door as they must be frozen up from rust.
How do you replace lock cylinder mustang?
If you are talking about the ignition lock cylinder, turn the key to the accessory position, insert a paper clip into the little hole on the face of the lock cylinder to release the lock pin, turn the key a little further in a counter clock-wise direction and the lock cylinder will pull out. If you are talking about a door lock cylinder, remove the door panel, roll the window all the way up, pop the little clip loose on the lock rod that is hooked to the back of the cylinder and remove the rod from the lock arm, then pull the 'C' clip out that is holding the lock cylinder in place and push the lock cylinder out.
How do you replace an ignition lock cylinder on a Chevy S-10?
Remove the retaining ring at the top of your Chevy S 10 ignition lock cylinder. Slide the ignition lock cylinder out. Remove the wiring harness from the back of the ignition lock cylinder. Reverse the process to install the new ignition lock cylinder.
How do you remove and replace an ignition lock cylinder on a 1994 Ford Bronco?
Begin by removing the retaining ring at the top of your 1994 Ford ignition lock cylinder. The ignition lock cylinder will slide out. Remove the wiring harness from the end of the ignition lock cylinder. Reverse the process to install your new ignition lock cylinder.
Why must a plug in a mortise cylinder lock be turned slightly before removing it from the cylinder?
You turn a mortise cylinder lock slightly before removing to release it from the lock housing. There is an obstruction in the lock design to keep the cylinder more secure in the lock. After you remove the holding screw from the lock body you can turn the cylinder slightly to release it and remove from the lock housing. Not all mortise cylinders are designed this way. Some of the cylinders unscrew from the lock housing after releasing the cylinder retaining screw.
How do you change the key lock cylinder on 1991 Chevy Corsica?
If you are talking about the ignition lock cylinder, the steering wheel must be removed and the column disassembled to access a lock screw which holds the ignition lock cylinder in the column. No key is required for this (unlike all other vehicle manufactures). If you are talking about the door lock cylinder, the door panel must be removed, and the lock cylinder retaining clip must be removed (again no key is needed, which is the same for all manufacturers). If you are talking about the trunk lock cylinder, it is easily accessible from inside the trunk. Those are the only types of lock cylinders in this type of vehicle. There is no specific lock cylinder named key lock cylinder.
How do you install ignition lock cylinder in a 94 Pontiac Bonneville?
Attach the wiring harness to the end of the ignition lock cylinder. Slide the ignition lock cylinder into the slot. Tighten the retaining ring at the top of the cylinder.
How do you install the ignition lock cylinder on a 84 Chevy blazer?
You will need to attach the wiring harness to the end of your 1984 Chevrolet Blazer ignition lock cylinder. Slide the cylinder into the cylinder slot. Secure the ignition lock cylinder with the retaining ring.
