0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
How to make a simple model on tidal energy?
To make a model showing tidal energy you will need a bucket, copper wire, magnets, a paddle, light bulb, and water. Place the magnets inside wire coils and attach the wire to the light bulb, fill the bucket with water, and use the paddle to make waves. The energy produced by the waves moving the magnets will create enough power to light the light bulb.
What is the resistor inside a light bulb called?
the wire in your light bulb is a resistor :)
How could you use a magnet to make the bulb light up?
This may take quite a bit of effort, as most incandescent light bulbs use a fair bit of current. Find the smallest bulb with the lowest operating voltage, from a small flashlight. Get as many turns as you can from your piece of wire, wrapping it around and around. Connect the bulb across the ends of the wire. One end goes to the centre contact and the other to the side of the bulb. (assuming a small Edison screw type bulb.) Now move the magnet rapidly inside the coil you made with the wire. The lamp will only blink during the movement of the magnet. By rapidly moving the magnet back and forth, you can generate an almost continuous supply of AC current and keep the bulb alight.
What is the main reason fore a light bulb to stop working?
the main reason for a light bulb to break is, the light bulb heats the tungstin wire. When the tungstin wire gets heated to much it breaks, causing thi light bulb to stop working.
Describe how a meter would be connected in a circuit too measure the voltage at a light bulb?
When connecting a volt meter to a light bulb to measure the voltage of the light bulb, run a third wire from where the wire enters the bulb to one terminal of the voltmeter and a fourth wire from the other side of the bulb to the other terminal of the voltmeter.
How do you use a light bulb as a resistor when charging a capacitor?
connect the light bulb to the positive wire like a inline fuse and then connect the wire to the battery it should just burn out the bulb
How do you make a circuit with a light bulb and battery?
Get your bulb, it should be a very small wattage (weak) one, get your battery and wires, connect one wire to plus side of abttery and other wire to minus side of battery, then connect to the bulb, you may have to play around a bit to find a connection that produces light.
How do you make to make the perfect curcuit?
The things you need for your curcuit are: A light bulb, Bell wire, A Battery and a conducter ex. pin, paper clip Attach the bulb together with the battery using the bell wire. With the two ends of the wire connect to the conducter and see if light bulb comes on.
Will two batteries and a wire make a light bulb light?
first of all, you need a bulb, a wire, and ONE light bulb. You clip the wire on the battery and touch the wire on the bottom of the light bulb
What do you need to have a simple circuit?
Take a battery, a wire and a little light bulb. Put the wire on the flat part of the battery then put the other end of the wire on the side part of the bottom of the light bulb. Put the end of the light bulb on the top of the battery, dont touch the wire to the top when the light bulb is on it because is either shocks you or doesnt work.
How do you make a battery light a light bulb?
Make a circuit with 2 wires a batery and a light bulb and touch wire to medle on light bulb
How do you connect the parts of a simple electric circuit together so that the light bulb lights up?
Simply connect the -ve of the bulb to -ve of the battery and +ve of bulb to +ve of battery using an electrically conductive wire, the bulb will light automatically.
How can lemon make a bulb light?
the Sparks on the copper makes the wire on the light bulb makes the 9v light bulb turn on.
What can i make with a battery light bulb and copper wire?
you can make the light bulb turn on. Ooh ooh i know. it's a circuit!
Testing a power io DAA-6V100 solid state contactor?
Use a small light bulb, such as 25-50 watt. Connect 120 VAC power to the big L1 terminal. Connect the big T1 terminal to the light bulb. Connect the neutral to the light bulb. The light bulb will be OFF. Connect another 120 VAC wire to the control input terminal #3. Connect another neutral to the control input terminal #4. The light bulb will now be ON. See the drawing at the bottom of: http://www.power-io.com/products/dda5075100.htm
What components do you need to make a simple series light bulb?
You need a Battery, Light Bulb, Ammeter, Switch.
How can you learn whether or not a material can conduct electricity?
You need a battery, a light bulb, and three pieces of copper wire, as well as the thing you want to test. Create a circuit by connecting each object to two others with the copper wire. Place one end of a copper wire on the positive side of the battery, the other end on the bottom of the light bulb. With the second wire, connect one end to the side of the metal part of the light bulb (where you see the ridges), and the other end to the object. With the last wire, connect one end to the object and the other end to the negative side of the light bulb. If the light bulb lights up, then the object is conducting electricity. If you have a large light bulb, it won't show as much light, or maybe no light at all, even if you have a conductive material. It is better to use a smaller light bulb for smaller batteries, so you can see the light.
