0
How do you connect the cable coaxial feed to the ethernet cable?
Wiki User
∙ 12y ago
You need a special adapter that usually run $17.
Wiki User
∙ 12y ago
Add your answer:
Earn +20 pts
What type of cable would be used for feed in to cable box?
Coaxial, RG-59.
What is a wire used to connect some computer to the internet?
An "Ethernet" cable. These are different size from normal telephone cables/connectors. They are usually yellow or green in color. You are also going to need a modem or modem/router to receive the internet feed from either a cable company, telephone wire, or DSL.
Is coaxial cable able to keep out interferance and carry long distances?
Coaxial cable is designed to shield the communications medium from EMI and maintain the integrity of wire transmissions. There are specific distances that various types of coaxial cable can travel without repeaters or bridge filters. The most typical distance for ethernet is about 100meters. High-Speed (DSL) cables can go up to a mile before performance suffers. There are several types of cable in use to support various transmissions. The older STP, Thinnet/RG-58 cable used for ethernet has been replaced by Category-5 cable. Radio feed-lines use RJ-58, LMR-400 or even hard-line "wave guide" between transmitter and radiator (antenna). Cable Television is really the only mass-broadcast medium that still uses cable. It's important to remember that the coaxial connections are as critical as the coax quality it self. An exposed ground-shield on one end of a cable can both radiate unauthorized emissions, as well as be subject to interference from external EMF sources.
Can you bury coaxial cable?
Yes, but it is best to feed it through a PVC pipe first. Then seal it to keep the elements out such as water etc.
How do you connect the coaxial cable feed to the ethernet connection on the computer?
Most current networks use UTP but you are describing a "thinwire" network. Thinwire uses coax and an Rg58 connection. UTP (Unshielded Twisted Pair) networks use RJ45 connectors. They look like an oversized telephone plug. You can purchase a thinwire modem for your computer if that's what you need, or you can get a hub that can act as a converter if your computer already has an RJ45 network connection.
How do let your lab top feed the psn threw it?
Your laptop can not feed the PSN to the PS3, the PS3 has to be connected to the internet with an ethernet cable or through WiFi not a USN or HDMI connection
How do you change the battery cables on a 1997 Nissan pickup?
Disconnect the cables at the 1997 Nissan battery. After following one cable to the other end, disconnect it then pull it out. Feed the new cable in the same way. Connect the non battery end. Do the same for the other cable then connect the cables to the battery.
What is the function of RG6 cable?
RG6 cable is a coaxial type commonly used for domestic video systems. It is most often used as a feed from an antenna or from a satellite dish to receivers. As well as RF signals, the cable can also be used to carry base band video signals although this is not a common application for this type of cable. There are a number of connectors used with it including F conectors, BNC, RF and UHF types.
How can I connect direct TV to a TV that only has a cable connector?
You can buy the leads from eBay etc.. If you have a DVD or Video player, you could always feed it through that instead.
How do you use a dvr?
Connect its input to the output of a cable box and DVR's output to your television. If you don't have a cable / satellite set-top box, and your DVR has a built-in TV tuner, connect its input to a coax cable from your wall (raw cable feed) or a TV antenna (over the air reception), and DVR's output to your television, then scan for available channels. You should be able to watch TV through the DVR and record TV shows onto it.
Is there anywhere to feed an amp cable through to the inside of the car from the battery on a 1999 mondeo 1.8 zetec?
You will have to drill a hole and feed the cable through that hole. Be sure and use a rubber grommet to prevent the cable from being cut.
What is the purpose of cable puller?
The purpose of a cable puller is to allow a system of wires to pull a heavier load. A cable puller will then be used to feed the cable through on this system.
