answersLogoWhite

0

By inserting ur lund in lugai,s choot.....

User Avatar

Wiki User

13y ago

What else can I help you with?

Related Questions

Show you the wiring diagram of tube light fitting with electronic choke?

wiring diagram of electronic choke in tube light


Where is Fluorescent light wiring diagram?

Fluorescent light fixtures typically have a wiring diagram on the label or inside the fixture. The diagram will show how to connect the wires for the ballast and the tube sockets. It's important to follow the wiring diagram carefully to ensure the correct installation and function of the light fixture.


How do you connect tube light?

To connect a tube light, first ensure the power is turned off at the circuit breaker. Remove the old tube light if applicable, then attach the tube light fixture to the ceiling or wall, connecting the wires according to the manufacturer's instructions—typically matching black (live) and white (neutral) wires. Finally, secure the tube light in place, turn the power back on, and test the light to ensure it works properly. Always follow safety precautions and consult an electrician if unsure.


Working of a Tubelight with Diagram?

A tubelight operates using a fluorescent mechanism that involves a low-pressure mercury vapor and a phosphor coating inside a glass tube. When an electric current passes through the tube, it ionizes the mercury vapor, producing ultraviolet (UV) light. This UV light then excites the phosphor coating, which emits visible light. A typical diagram of a tubelight would show the tube, ballast, starter, and electrical connections. Here's a simple diagram representation: +-----------------------+ | | | Tubelight | | | +-----------------------+ | | | | Ballast Starter | | | | Power Supply


How does a tube light works?

tube light woks like a tube light....


How a tube light works?

tube light woks like a tube light....


How can I effectively install a solar tube in my basement to maximize natural light and energy efficiency?

To effectively install a solar tube in your basement for maximum natural light and energy efficiency, follow these steps: Choose a location in the basement where the solar tube can capture the most sunlight. Cut a hole in the roof and ceiling for the tube to pass through. Install the flashing and seal the tube to prevent leaks. Connect the tube to a reflective light tube that directs sunlight into the basement. Ensure the tube is properly insulated to prevent heat loss. Consider adding a light diffuser to evenly distribute the natural light. Regularly clean the tube to maintain optimal light transmission. By following these steps, you can effectively install a solar tube in your basement to maximize natural light and energy efficiency.


Is it possible to connect two tube lights with a single choke and also you need the circuit to connect the tube lights?

yes


Which connect the eyepiece to the revolving nosepiece with the objectives?

The draw tube and the body tube connect the eyepiece to the revolving nose-piece.


How do you replace the knock sensor 2001 mercury villager?

BEFORE YOU DO THIS: Be aware that if you are doing it because of a a knock sensor code, it is most like uneccesary. A knock sensor is a passive device that has no effect on normal engine operation. Mercury Villagers are notorious for throwing knock sensor codes when nothing is in fact wrong with the knock sensor (which produces no current under normal conditions). Because of the way emission components are wired, problems in front oxygen sensor wiring harness (common) or the throttle position sensor can also cause this code to be set. Many of these sensors are replaced uneccesarily. Know also that this is a fairly involved job which will take the better part of an afternoon if you are fairly skilled. You will need to drain and refill the cooling system, and you will be disassembling a number of pipe connections that have to be reinstalled with either aftermarket gaskets or assembled with RTV, which can be tricky to get right without leaks. Here is the procedure for replacing the knock sensor on a '01 Mercury Villager: --Removal-- 1. Remove the lower intake manifold. 2. Disconnect the heater core hose from the coolant crossover tube. (refer to the diagram in the 'related links and sources' portion of this answer) Release the clamp and disconnect the hose. 3. Release the clamp and remove the lower radiator hose from the coolant crossover tube. 4. Remove the water bypass hose from the thermostat housing. Release the clamp and remove the hose. 5. Remove the coolant crossover tube. Remove the bolts and tube. 6. Remove the Knock Sensor (KS). Disconnect the electrical connector. Remove the bolt. --Installation-- 1. Install the knock sensor and bolt. Connect the electrical connector. 2. Install the coolant crossover tube. Position the coolant crossover tube. Install the bolts. 3. Install the water bypass hose. Position the hose. Position the clamp. 4. Connect the lower radiator hose to the coolant crossover tube and position the clamp. 5. Connect the heater core hose to the coolant crossover tube. Connect the tube. Position the clamp. 6. Install the lower intake manifold.


What is full form of tube light?

tube light


What will be the name of tube light in urdu?

tube light