answersLogoWhite

0


Best Answer
Copy

To fix it I would recommed taking it to your nearest Ford/Lincold/Mercury dealership. If it is stuck forward however..... Where the belt should be in the driving position there is a screw, take it out. There is a manual override in there, turn it clockwise until you can move the belt to the proper position.

Spyder

User Avatar

Wiki User

โˆ™ 2015-07-15 21:17:17
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0
User Avatar

Add your answer:

Earn +5 pts
Q: How do you fix a retractable seatbelt on a 1993 Mercury Cougar?
Write your answer...
Submit

Related Questions

How do you change water pump on 1993 Mercury Cougar?

how do you change a water pump on 1993 Mercury Cougar


Brake fluid 1993 mercury cougar?

A 1993 Mercury Cougar takes ( DOT 3 brake fliud )


What type of refrigerant does a 1993 Mercury Cougar use?

What type of freon does a 1993 cougar use


Where is the module located on a 1993 Mercury Cougar?

In the trunk


Where is the voltage regulator on 1993 mercury cougar?

embedded with alternator


What was the original price of a 1993 Mercury Cougar?

the orignial price was $17,890


What is the spark plug gap 1993 Mercury Cougar?

.040 ========================================================== According to one of Fords websites : For a 1993 Mercury Cougar : The 3.8 liter V6 engine and the 5.0 , V8 have spark plugs gapped at : ( .054 inch )


Removal of water pump on an 1993 mercury cougar Rx-7?

ok


How do you open the fuel door on a 1993 Mercury Cougar?

A button inside the glove box.


Where is the radiator drain located on a 1993 mercury cougar XR7?

on the bottom of the rad on the passenger side


What is the fuel tank capacity for a 1993 Mercury Cougar?

The fuel tank capacity is 18 gallons


Where is the therostat located in a 1993 Mercury Cougar V8?

where the upper rad hose meets the engine


Type of brake fluid 1993 Mercury Cougar?

DOT 3 will work just fine


How do you replace lower ball joint on 93 Mercury Cougar?

Remove the tire and wheel from your 1993 Mercury Cougar. Remove the ball joint retaining nut. Pound the ball joint out with a hammer. Reverse the process to install your new ball joint.


How do you drain transmission fluid on a 1993 Mercury Cougar?

Just like all automatic transmission cars, remove the oil pan.


Where is the fuse box located on 1993 mercury cougar?

Left of stearing wheel, under the dash (get ready for some strange angles!).


How do you take the head light dome light switch off on a 1993 Mercury Cougar?

You don't. The switch is all one , you will have to replace the entire switch.


Is the engine for a 1993 Ford Thunderbird 3.8Lthe same as the engine for a 1994 Mercury Cougar Xr7 3.8L engine?

you can put a 5.0L and everything will be fine!! =]


How do you remove the door panel on a 1993 Mercury Cougar XR7?

To remove the door panel on a 1993 Mercury Cougar XR7, the first thing to do is to remove the lens covers from any lights in the door. The unscrew the light fixtures from the door. The door panel is attached by the use of clips. With a little nudging with a flat object, such as a screw driver, the clips will pop free of the metal.


1993 mercury cougar firing order with a v8?

1-5-4-2-6-5-3-7-8 Distributor rotates counterclockwise.


Where is the head gasket located on a 1993 Mercury Cougar?

Between the head and the engine block. under the cylinder head v-* motors have 2 heads and gaskets


Why would the horn on a 1993 Mercury Cougar XR7 suddenly become very quiet and only sound one tone?

Poor ground, or defective horn.


What kind of fuel do you use in a 93 Mercury Cougar?

Both engines in the 1993 Cougars (V6 or V8) operate just fine on 87-octane fuel.


How do you fix door latch on a 1993 Mercury Cougar that only work half the time?

get a hinge replacement kit for that door. its the door sagging NT the latch.


How do you change rear wheel bearings in a 93 cougar?

Remove the wheel from your 1993 Mercury Cougar. Loosen and remove the wheel bearing nuts. Remove the wheel seal and the wheel bearing. Reverse the process to install your new wheel bearing.