Read the instructions which should come with the baseboard wire track.
<><><>
It is the easiest when you can hide wires behind the walls.
<><><>
As always, if you are in doubt about what to do, the best advice anyone should give you is to call a licensed electrician to advise what work is needed.
Before you do any work yourself,
on electrical circuits, equipment or appliances,
always use a test meter to ensure the circuit is, in fact, de-energized.
IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOB
SAFELY AND COMPETENTLY
REFER THIS WORK TO QUALIFIED PROFESSIONALS.
Depends on the Amperage of each baseboard heater (how many watts each one draws).
The white is neutral. The house does have a neutral wire even though it may be black. One of those black wires is the neutral and the other is the hot wire. You will have to determine which is hot and which is neutral. You can easily do this with a voltage tester. The wire that lights the tester is the hot. When you wire the light simply wire the hot to hot, and the white and green to the other wire.
1600 watts is unusually low for electric baseboard heaters! These usually are rated at about 6000 watts.Typical electric baseboard heaters operate on 220 volts thus you heater would pull about 7.3 amperes and 16 gauge wire can easily handle this.A standard 6000 watt baseboard heater pulls about 27 amperes and needs 10 gauge wire.
If single phase - 2 wire service > two wires If single phase - 3 wire service > three wires If three phase - 3 wire service > three wires If three phase - 4 wire service > four wires US residential service is usually single phase 3 wire service: Two hots and neutral.
The wires must first be heat resistant. For that the best wires that can be used are wires made up of superconductors.
In the heater you will have two wires. You should then have 2 supply wires from the panel, and 2 wires from the thermostat. The neutral (white) supply wire should go to one of the wires on the heater. The hot (black) supply wire should connect to one wire from the thermostat. The other wire from the thermostat will connect to the other wire from the heater.
In wall speaker wire is useful, as it hides the wires from sight. When a surround sound system is installed, it can lead to a number of unsightly wires appearing around the room. In wall wires hide this problem.
Most baseboard heaters use hi voltage thermostats.
You should attach one end of each wire wire first to the track where the two recivers for the wires are, and then hook the other ends of the wires to the power pack. *MAKE SURE POWER PACK IS OFF BEFORE ATTACHING ANY WIRES* After you have attached the wires you can turn on or plug in the power pack and run your model trains.
Depends on the Amperage of each baseboard heater (how many watts each one draws).
The white is neutral. The house does have a neutral wire even though it may be black. One of those black wires is the neutral and the other is the hot wire. You will have to determine which is hot and which is neutral. You can easily do this with a voltage tester. The wire that lights the tester is the hot. When you wire the light simply wire the hot to hot, and the white and green to the other wire.
1600 watts is unusually low for electric baseboard heaters! These usually are rated at about 6000 watts.Typical electric baseboard heaters operate on 220 volts thus you heater would pull about 7.3 amperes and 16 gauge wire can easily handle this.A standard 6000 watt baseboard heater pulls about 27 amperes and needs 10 gauge wire.
The red wire is the positive wire. The black wire is the ground wire. The green and yellow wires are the speaker wires. The white wire is the auxiliary wire.
The Ford audio wires consist of five different colors. The red wire is the positive wire. The black wire is the ground wire. The speaker wires are green and yellow. The auxiliary wire is white.
first of all you buy a double pole unit thermostat which should come with the mounting plate and thermostat and it should have 4 wires 2 red 2 black okay now you join the red to the red power wire and black to the black power wire and the 2 remaining wires which should be a red and black can be joined to the red and black wires on your heater .....now you should be good to go ............LEE48
form_title=Install Speaker Wires form_header=If you're setting up a surround sound system in your house, hide those unsightly wires. How many speakers does the system include?=_ Describe the room where the speakers will be installed?=_ Are you experienced in installing spaker wire for home installation?=_
The red wire is the positive wire. The black wire is the ground wire. The green and yellow wires are the speaker wires. The white wire is the auxiliary wire.