On a 240 volt outlet, such as a dryer outlet: G is Ground, W is Neutral, X and Y are the two Hot legs.
No, and adapters are not needed. What needs to be done in remove the old three blade dryer plug and install a new four blade cord on the dryer.Dryer plug three to fourInstructions should come with the new cord. Open up the electrical access panel on the back of the dryer. You will see a terminal block with three wires going into it from the plug cord assembly. A red and black and white are now connected to the terminal strip. Look at the position and colours of the existing 3 prong cord and how it is connected. Make a diagram. Coloured wires on the outside terminals white in the center. From the center wire terminal you will see a jumper strap that goes to the frame of the dryer. When installing the four prong plug this jumper is removed completely. The kit should have with it a grounding lug that connects to where the removed grounding strip attached to the frame of the dryer. This is the attachment point for the fourth green ground wire from the new dryer cord assembly.
On a 240 volt outlet, such as a dryer outlet: G is Ground, W is Neutral, X and Y are the two Hot legs.
Go to this site http://www.generatorjoe.net/html/nemaplugs.html and tell me what configurations you have and I might be able to help you.
There is no requirement on the distance the dryer must be from a sink. Any 120 volt outlet must be GFCI protected if it is within 6 feet of a sink. There is no requirement for a 240 volt dryer outlet. I would not want the dryer right next to the sink and I would want the dryer to be on a 4 wire circuit and not a 3 wire circuit. Use common sense here.
Only if you wanted to fry your hair.for God sake(and yours)buy a new cord to hook up your dryer
No you can not you will need to replace the plug with a 4 prong the same as the style of your oven and change your breaker to the correct Amp for your style of 4 prong plug
Change either the plug or the cord. The fourth prong is another ground. It would be easier to change the cord.
At any DYI store.
A qualified electrician should make the change to a dryer connection. The best way to cheaply make the change is to change the power cord on the dryer to the three hole standard.
I just have an adapter that i keep in the back of my explorer that goes from a 4 to 7 prong trailer hook up
Probably not. The reason is the amperage required by the electric range. They typically require 50 amp whereas a dryer normally only requires 30 amp. Therefore, the wiring feeding the dryer is not large enough to support an electric range. Your range should be wired with #6 or 8 gauge wire, whereas your dryer is likely only wired with # 10 gauge which will not carry 50 amps.
It may be a 220 Dryer, and you will need a new outlet installed. There should be no extra wires when connecting the Power cord to the plug
To adapt a three prong range cord?æto a four prong outlet you need to remove the screws from the back plate to open the electric access panel. Then, pull out the copper grounding strip attached to the middle terminal. Next, remove the green ground screw from under the terminal block and attach it to the four prong outlet.?æ
Depending on your PDA, you'll need either a 3 prong or a 4 prong cable with a UBS on the other end.
Dryer plug three to fourOpen up the electrical access panel on the back of the dryer. You will see a terminal block with three wires going into it from the plug cord assembly. A red and black and white are now connected to the terminal strip. Look at the position and colours of the existing 3 prong cord and how it is connected. Make a diagram. Coloured wires on the outside terminals white in the center. From the center wire terminal you will see a jumper strap that goes to the frame of the dryer. When installing the four prong plug this jumper is removed completely. The kit should have with it a grounding lug that connects to where the removed grounding strip attached to the frame of the dryer. This is the attachment point for the fourth green ground wire from the new dryer cord assembly.
The four blade dryer plug brings a separate ground wire from the machine to the electrical grounding system. The three blade dryer plug depended on the neutral wire of the plug to make this connection.