1995-1999 Dodge & Plymouth Neons

How do you install a cold air intake on a 1998 Plymouth Neon 20 DOHC?

151617

Top Answer
User Avatar
Wiki User
2005-09-24 09:01:30
2005-09-24 09:01:30

I think you have to move the battery to the trunk. I got a new intake system for my 1995 neon and just had to remove the factory system first. Try going to Procarparts.com .This is where I got mine from. Hope this helps..

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

The intake valves can hit the exhaust valves.

User Avatar

A 1998 Plymouth Breeze with the 2.0 SOHC engine requires 4 quarts of oil, and the 2.4 DOHC engine needs 5 quarts of oil.

User Avatar

SOHC and DOHC engines are different. Please ask question again specifying engine.

User Avatar

Pull off the upper intake plenum and you will have access to the plugs and wires.

User Avatar

Your sensor is part of the MAP sensor which is located On the SOHC look behind and to the left under the top radiator hose you'll see the wires going into a fitting. On the DOHC it's to the right of the oil dipstick under the fuel rail.

User Avatar

There are 2 options, 8valve 115bhp sohc and 16valve 147 bhp dohc, if you open the bonnet the 16v dohc has an unmitakable intake manifold and DOHC 16 v badge is on the casting. hope this helps There are 2 options, 8valve 115bhp sohc and 16valve 147 bhp dohc, if you open the bonnet the 16v dohc has an unmitakable intake manifold and DOHC 16 v badge is on the casting. hope this helps

User Avatar

It is located on the front valve cover under the cover that says "duratec 24v dohc"

User Avatar

The water pump is timing belt driven. You should buy or borrow a service manual, as this is a very intensive repair.

User Avatar

DOHC - Dual Overhead Cam. This means that there is an intake and an exhaust cam, allowing the valves to move differently for the intake and exhaust. SOHC uses a single cam with more lobes

User Avatar

96-99 dodge neon dohc and 1995 fits by changing upper intake

User Avatar

no the smallest the company put in a laser was a 1.8

User Avatar

The intake air temp sensor is located on the cover over the air filter.

User Avatar

torque for bolts upper intake 1999 ford taurus 3.0 dohc

User Avatar

what is the torque cylinder head bolts and the camshaft for KIA clarus 2.0 petrol DOHC 1998 model

User Avatar

The camshaft position sensor is located beneath the wheel on a 1998 Ford Taurus 6 cylander Dohc.

User Avatar

they can have the 2.0 DOHC 4g63 the 2.0 DOHC turbo 4g63t and they came with a 1.8 DOHC but I don't know the engine model. Just an FYI, the 1.8L motor in DSMs was a SOHC and had an engine code of 4G37. Cheers!

User Avatar

remove plastic cover that dohc 24 valves and that big black mess going from front to back of motor is the intake

User Avatar

In a dual overhead cam (DOHC, twin cam, etc.) engine, the intake cam is the camshaft contolling the intake valves. Thus the opperation of the exhaust valves is left to the exhaust cam.

User Avatar

Anything is possible, but it would take major modifications.

User Avatar

nothing. only if it is a dohc or a sohc.

User Avatar

You could simply install headers, a cold air intake, and exhaust system, but even that costs several hundred dollars. If you want a whole lot of power on demand, you could also install a nitrous-oxide kit. They practically bolt right in.

User Avatar

standard will have a single overhead cam the espresso will have a dual over head cam all the front hood will have a bulge on the passenger side of the hood that is one way to identify that this is a dohc.


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.