If it's new, you may have to cut it to fit.
You don't need to remove the fan to install it, just slide it in between the fan and the radiator. It will be a very tight fit, just go slow. Once it's in, you will need to install the 4 bolts on the top, and 2 on the bottom.
The schematic should be on the fan shroud.
its under the drivers side dase
The Haynes manual wants you to remove the fan and the shroud as a unit. This requires disconnecting the electrical connections to the fan, removing the bolts that hold the fan/shroud to the car, and just slipping the shroud off it's mounting tabs and removing. NOTE; that Haynes recommends removing the negative battery cable before starting the job. FriPilot
No but sometimes it makes it easier The serpentine belt is easily removed without removing the fan shroud This has to be accomplished by using a tensioner wrench
This information should be on the fan shroud.
look at the diagram that's on the fan shroud
Drain the radiator. Remove the fan and fan shroud if needed. Remove the pump belt. Unbolt the pump and remove it. Install the new pump. Reinstall the belt, fan and fan shroud. Refill the system with new coolant.
== 2.3L Engine # Unbolt and remove the fan guard. # Disconnect the overflow tube from the shroud, remove the mounting screws and lift the shroud off the brackets. # Place the shroud behind the fan. # Remove the 4 clutch/fan assembly-to-pulley screws and remove the clutch/fan assembly. # Remove the 4 fan-to-clutch screws. To install: # Position the fan onto the clutch assembly, then install the retaining screws to 55-70 inch lbs. (6-8 Nm). # Position the clutch/fan assembly onto the pulley. Install the mounting screws to 12-18 ft. lbs. (16-24 Nm). # Position the fan shroud onto the radiator. Install the shroud mounting screws until snug. # Install the fan guard. 2.8L, 3.0L and 4.0L Engines # Remove the accessory drive belt. For more information, refer to Section 1. # If necessary for added clearance, remove the fan shroud retaining screws. CAUTIONThe large nut which attaches the fan clutch to the hub of the water pump shaft has a right-hand thread and must be rotated clockwise for removal. # Using the Fan Clutch Holding tool T84T-6312-C and Fan Clutch Nut Wrench T84T-6312-D, or their equivalents, loosen the large nut attaching the fan clutch to the water pump pulley. # Remove the fan/clutch assembly. # Remove the fan-to-clutch bolts, then separate the fan from the clutch assembly. Fig. 1: The cooling fan mounts to the fan clutch, which in turn attaches to the water pump pulley - 3.0L and 4.0L engines Fig. 2: Use the two fan clutch tools to remove the fan clutch from the water pump pulley To install: # Position the fan onto the clutch assembly, then install the fan-to-clutch mounting bolts to 53-71 inch lbs. (6-8 Nm). # Position the lower edge of the fan shroud in the lower retaining clips, then install the fan shroud attaching screws until snug. # Using the holding tool and clutch nut wrench, or equivalent, install the fan/clutch assembly onto the water pump pulley. Remember, the fan/clutch nut has a reverse thread and must be turned counterclockwise to tighten. Tighten the nut to 30-100 ft. lbs. (41-135 Nm). # Install the accessory drive belt.
How do you remove the fan shroud on a 2004 get envoy
With engine cool, drain coolant. Remove two bolts at top at shroud then lift shroud off of lower clips. Turn shroud until you can get your hands inside to take the fan bolts out. After the fan is loose, take the four water pump to fan adapter bolts out. Lift shroud off. Continue on, learning new swear words when you come to the idler over the timing cover...
is it 4 cly or v6? if it is a v6 you can take the fan off, or pull the radiator out.4cyl I'm pretty sure you got to pull the fan off.
Drain the radiator, and dispose of the fluids as it is toxic to animals. Remove the water pump belt. Take off the fan and fan shroud if they are in the way. Unbolt the pump, remove it, then install the new pump. Replace the belt, fan and shroud, then refill the radiator with new coolant.