0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
Does splashes have 2 syllables?
It has 2 syllables spash-es
Does spash work in Pokemon?
it may not work in battle but it does work well in contest so you in compeate in contest then use spash. ofr any Pokemon facts check out bulbagarden.net it will tell you all you need to know about Pokemon if you search it
What do goldfish like to do?
play with goldfish mates, swim, hide, spash around, and eat.fish are coolswim
In Super Smash Bros. melee what does the Magikarp do?
Nothing at all. he just flops around using spash
How do you change oil in a 2003 G.M.C. envoy?
under the vehicle, there is a spash guard protecting the engine. in this spash guard there is an approx 6 or 8" door panel. using a flat head screwdriver turn the screw a quarter turn to the left. the panel will be loose, spin the panel so it out of your way. the drain plug is right there and a little put up in the hole is the filter.
What is the easiest thing to cook?
scrambled eggs. a few eggs in a bowl and add a spash or two of milk. whisk them together with a fork or whisk and cook them in a frying pan until they look cooked. (not runny) you could even toast up some bread and top it with your lovely creation.
How do you Replace oil-pan gasket on 1990 Buick skylark?
I have a 1990 Buick Skylark and I need to remove the oil pan. How do you do it ? Help!! Just remove the spash shields in the way of the pan then remove the bolts from the pan and replace the gasket. You can find Buick manuals from Chiltons on Amazon for these cars. They're cheap nowadays.
Mercedes Benz CLK 550 Oil Pan drain plug location?
i have a 2007 clk 550 convertible. the oil drain plug is located in the back of the engine towards the driver side. you need to get under the car and remove the front and back cover to expose the oil pan and drain plug. the drain plug is at the front of the oil pan towards the driver side. it is located at the side of the oil pan, not at the bottom as other cars. easiest way to get to it is from the front of the car. the 550 holds 9 qts of oil and you'll need a large oil collector. with the convertible, mercedes had two cross braces under the car for reinforcement. one of them it just right infront of the drain plug.. because the plug is on the side of the oil pan, once the plug is loose, oil will spash towards the engine parts and the cross brace and get oil everywhere. i tried to put some paper up there to cover the engine parts but it end up soaking up the paper and still spash oil all over.. you need to look at it closely and figure a way around that. i think i'll cut open a gallon container and push it up towards the oil drain plug and let the oil spash toward the gallon container and then drain to the oil collector. you'll need a oil filter wrench, 74mm with 14 sections, can get one from autozone for 6.00 and they work fine.. but you should only use mann oil filters they are the same one mercedes uses..
Where can you find a manual with a picture of the location of the starter in a 1991 Buick Regal?
Your cheapest bet is to go to loacal library and look in a Chiltons manuel, and get copies of page for about 10 cent. The manual may not have pictures though. For best view jack up the front of the car and remove the plastic spash pan cover. The starter is on the face of the motot in the middle, obout the center of the radiatot at the bottom. Don't forget to dicconnect the battery before working on the starter.
How do you properly adjust lifters or rocker arms on Chevy 283?
Assumming you don't have a roller or solid lifter cam ( those get adjusted with a feeler gauge ) , the best way I've found is the following: 1) warm the motor to normal temp. 2) remove one of the valve covers and install splash clips ( JEGS sells them ) on each rocker OR take an old steel valve cover, cut the center out so you can get a socket oneach of the rocker nuts, and install that in place of your pretty ones. 3) start the engine and let it idle 4) SLOWLY loosen the first rocker arm nut until you hear that lifter tap. Then SLOWLY retighten the nut until the tapping stops. 5) If you want more topend power, tighter the nut another 1/4 to 1/2 turn. If you want more bottom end power, tighten the nut a full turn past where it stopped tapping. 6)repeat this for each lifter on the first side 7) remove the spash clips or modified valve cover and install your shinny one 8) repeat on the other side 9)if they seem to go out of adjustment quickly invest in 16 new rocker arm nut from the dealer and do the same procedure again 10)BIG THING is adjust slowly and keep things clean 11) good luck !!!
How can you make a stock ATV pipe louder?
Making a motorcycle exhaust louder can be achieved by removing the baffle in the muffler, or shortening the length of the muffler. If applicable you can also change to a high volume end cap. Note that several countries have regulations regarding noise levels from vehicles. Remember to check with your local road vehicle authority to make sure you will not be fined.
Where is the oil filter on a Mazda 3?
if you look under the front of the car, there's a plastic splash shield that needs to come off. on 2.0L cars, there's a cutout that lines up (I'm told) with the filter, so you don't have to take off the whole shield. But on 2.3L cars like mine, the hole doesn't line up. it's much less messy to just take off the spash shield anyway. also, be careful, 2005 and earlier 3's have a filter cartridge, whereas 2006 and later (I think that's the cutoff) have a traditional spin-on filter. good luck.
