0
How do you keep the shaft from turning when tightening nut on blade?
Wiki User
∙ 7y agoWant this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
What would keep the crank shaft from turning in a 1995 jeep wrangler?
A bent rod or piston arm.
How do you remove a table saw blade?
unplug it clamp a pair of vise grips tightly to blade turn it up on end find the correct size socket for the bolt on the hub it should unscrew clockwise (vise grips keep blade from turning) pull the blade out the top with the vise grips put the new blade on in reverse order
Why does your lawnmower make a rasping sound when the blade stops?
What you are probably hearing is the little "brake pad" (for lack of a better term) that the blade pulley rubs against to stop it from turning. The belt always turns. So without something to keep the blades from turning they would never stop.
How do you put the replacement blade on the shaft?
replacing a blade takes a lot of practice and the right tools so unless you want to bugger up your stick, it would be a good idea to take it to a shop and get it done for a couple bucks(plus the cost of a blade)...if you want to do it on your own you'll need the right glue and a torch. the amount of heat depends if you have a composite shaft or (unlikely) an aluminum one. using the torch keep the flame visible(orange or red or whatever) and roast the end of the shaft like a hotdog. constantly move it right to left while rotating slowly. check every couple of seconds by trying to pull out the blade. once out put some glue in thin strips on all 4 sides of the blade and a little inside the shaft. heat the glue on the blade a little and shove that thing up there
How do boats with holes in their hulls for the propellar keep out water?
The propeller is at the end of a shaft. The shaft passes through a fitting called a stuffing box. The stuffing box contains a material like cotton or waxed twine that wraps around the shaft. There are two or more bolts that hold the stuffing box together and by tightening or loosening the bolts you can squeeze or release the stuffing material to the shaft. Ideally you tighten the bolts to the point that water just drips in. This allows the shaft to spin freely. It is lubricated by the water. If you tighten the box too much then you can score the shaft. The water that drips in is usually pumped out by a bilge pump.
How do you tow dolly a 1966 mustang?
The best way would be to remove the drive shaft from the vehicle before towing. Many transmissions do not circulate the transmission oil or fluid unless the engine is running. Removing the drive shaft will keep the rear output on the transmission from turning while towing it.
Brush Cutter Blade?
form_title= Brush Cutter Blade form_header= Keep your landscaping beautiful with a brush cutter blade. What size blade do you need?*= _ [50] What brand do you prefer?*= _ [50] Are you replacing an old blade?*= () Yes () No
How do you keep a toilet seat from slipping sideways?
Buying the proper size, and tightening the nut and washers.
What is the cooling system of gas turbine blade?
In order to enhance creep life of gas turbine blade, it is required to keep blade at lower temperature, hence internal cooling of blade is done.
How do you keep coleslaw from turning brown?
sprinkle with lemon juice
How do you get the pulley off of a 12.5 Briggs and straton motor?
You need a socket with a long extension to go through the center of the pulley/shaft to locate the nut. You will have to block the pulley or the motor to keep it from turning while you are removing/replacing the nut.
How do you keep your front wheel on your scooter to stop turning off axis. I tried tightening the clamp but it keeps slowly loosening?
need to get a slit on the botom part of your handlebars on your scooter and if you aleady have a slit, then take it to the shop and get a bigger slit and push your clamp all the way down.
