0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
How do you make a screen house?
take some wood and make a frame and door then attach sreening. easy
Is it good to cut away 2 inches off a door frame to install a dead bolt lock?
What kind of lock are you considering that requires you to take 2 inches off a door frame and at what point are you removing it? First response is to say no. I can only imagine that this would make the door and frame less secure.
Will 1970-1981 firebird doors fit camaro?
if same year the frame of door will be same. but door pannel isn't same. you can make it work
What is the difference between a flush door and a panel door?
A flush door has panels that are mostly flat and take up the entire space of the door. A panel door has loose fitting panels that fit into grooves that make up the frame of the door.
What steps are taken to install a new set of sliding doors?
First, someone must select the doors and choose the room they are going in. Then, they will cut the drywall to make room for the door and then construct a frame. When the frame is done, the door should be installed. Once the door is in place, the area around the door should be dry walled again.
Is the black vinyl tape around the door frame on a 2007 Hyundai Sonata supposed to be removed?
Yes, the black vinyl tape around the door frame on a 2007 Hyundai Sonata can be removed. It was placed there during the manufacturing process to make sure the seal around the door stayed in until the glue set.
If a door frame opening is 32 inches how large of a screen door do you need?
You will need a "2 6" or 30" wide door. Make sure your rough opening height is around 82 1/2".
Which is better steel or fiberglass doors?
I think steel doors are much better when compared to fiberglass doors in terms of strength. If you are planning to install a steel door here are easy steps to do it : Firstly, use a pry bar in order to pull the upper molding of the existing door. Repeat the steps again on the bottom as well as the middle part of the molding. Get the hige pins out and then unscrew the hinges. Next, work on the wall framing. Start placing the metal studs on the new frame opening. By using a set of screws, you can secure the frame directly into the existing sill and header framing. Block the areas which require support. Next, you have to set up the door. You may need another person to help in this process. Place the bottom of the steel door in the door opening. Tilt the steel door up into place. Using the shims, make sure to level and orient the door in the right position. Now you have to shim the door. You have to manupulate the shims on each side of the door frame between the metal studs and frame. This will make the door to plumb and level. Then you need to screw the lockset portion of the frame to the metal studs and do the same to the hinge of the frame. Happy to help you.
How To Install A Sliding Glass Patio Door?
Adding a sliding glass patio door to your home can make a world of difference not to mention that it adds a great deal to the value of your home. However, hiring someone to do this for you can get quite costly. If you are confident in your handyman abilities, here is a guide to get you through the installation of your new sliding glass patio door. If you are not confident in your handyman skills, hiring a contractor may actually save you from costly mistakes that can occur from an improperly installed sliding glass patio door. Step 1. The first thing that you will need to do when you are installing a sliding glass patio door is to make sure that you have all the necessary tools and materials needed to complete this job. You will need either metal screws or mounting hardware included with your sliding glass doors, self adhesive foil tape, a razor knife or other cutting instrument, caulk, measuring tape, level and low-expansion foam insulation sealant. Step 2. You will need to apply your foil tape around the sill of the door and six inches up the sides of the door jamb. When you are trying to fit the tape in the corner areas, you can make any cuts that are necessary to allow the tape to wrap around or sit flush on the corners. Step 3. Now that you have the start of your foil tape installed, continue applying the foil tape around the entire outer edge of the door frame. Make sure that you use the same method as above to work in the corners. Step4. Inspect your original door to see if it had a sill support. If it did, you will need to replace it. If it did not, you can skip this step. Step 5. Apply three lines of caulk on the foil tape that is on the bottom of the door. Make sure that they run next to each other. Step 6. Measure your door to make sure that it will fit into the frame that you have correctly. If there are any adjustments that are necessary to make to the door now is the time to do this. Step 7. Without sure not to disturb the caulk lines that you placed on the door in step 5, you will need to set your door into the frame. This will work best by starting at the bottom of the door working your way up until the door is in an upright position. Step 8. To make sure that the door is held in place you will need to attach any supports that you for the door frame at the top. Use your level to make sure that your door is flush with the door frame. If it isn’t you will need to make the necessary adjustments to the door or frame as needed. Step 9. You will need to install the latch and latch holder to the door. Finish fastening the door to its frame. You can either use the mounting hardware that came with your door or use roofing nails. Step 10. Place caulk in the screw holes located on the bottom of your door. Insert any necessary screws needed to hold the door in at the top and bottom. Step 11. Place another layer of your self adhesive foil tape on the supports and set any glass portions you have for the door itself into the frame. Step 11. Use your foam sealant and apply it around the door frame. Replace any of the trim that you removed from the original door or place any new trim in place inside and outside of the home.
Make share you Cheak www.google.edu.au?
YES , the fuel filter is underneath the Explorer , on the drivers side , below the drivers door , mounted on the frame rail
Can you put a metal front door onto a wooden frame?
I did it and the result is not too bad...it will not keep thieves out of my home but they wiil make a lot of noise to get into my house..
How do you measure up to make curtains?
To make curtains, you should measure from the floor to the top of the door or window frame. You will want to add a couple of inches to include the part that covers the curtain rod.
