0
♥Do you know how to tighten your seat belt? If so, do the same with the belt. Or depending on your size ask your school or communty to get a belt for you.♥
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
What can someone People who worry that a safety belt wrinkles their clothes can?
It is important to wear the safety belt while riding or driving a car. If a person is worried about their clothes wrinkling they can buy a seat belt cover, or make sure they flatten the seat belt out.
Wearing safety belt make you save but do not protect you from drunk drivers true or false?
It is true that safety belts will keep you safe but will not protect you from drunk drivers.
How do you change kawasaki 360 prairie drive belt?
Remove side cover, remove clutch ( primary the smaller clutch) and belt will come off easy. Make sure to install new belt with arrow on belt pointing in the right direction (forward)
How do you disable the seat belt alarm in a ford?
Deactivating/activating the belt minder feature Read steps 1 - 9 thoroughly before proceeding with the deactivation/activation programming procedure. The Belt Minder feature can be deactivated/activated by performing the following procedure: Before following the procedure, make sure that: ² the parking brake is set ² the gearshift is in P (Park) (automatic transmission). ² the ignition switch is in the OFF position ² all vehicle doors are closed ² the driver's safety belt is unbuckled ² the parklamps/headlamps are in OFF position (If vehicle is equipped with Autolamps, this will not affect the procedure.) To reduce the risk of injury, do not deactivate/activate the Belt Minder feature while driving the vehicle. 1. Turn the ignition switch to the RUN (or ON) position. (DO NOT START THE ENGINE) 2. Wait until the safety belt warning light turns off. (Approximately 1 minute) ² Steps 3--5 must be completed within 60 seconds or the procedure will have to be repeated. 3. Buckle then unbuckle the safety belt three times, ending with the safety belt unbuckled. This can be done before or during Belt Minder warning activation. 4. Turn on the parklamps/headlamps, turn off the parklamps/headlamps. 5. Buckle then unbuckle the safety belt three times, ending with the safety belt unbuckled. ² After step 5 the safety belt warning light will be turned on for three seconds. 6. Within seven seconds of the safety belt warning light turning off, buckle then unbuckle the safety belt. ² This will disable Belt Minder if it is currently enabled, or enable Belt Minder if it is currently disabled. 7. Confirmation of disabling Belt Minder is provided by flashing the safety belt warning light four times per second for three seconds. 8. Confirmation of enabling Belt Minder is provided by flashing the safety belt warning light four times per second for three seconds, followed by three seconds with the safety belt warning light off, then followed by flashing the safety belt warning light four times per second for three seconds again. 9. After receiving confirmation, the deactivation/activation procedure is complete.
What Fuse disarms the seatbelt warning alarm on a 2007 Ford Tarus?
You can Deactivate the Belt Minder two ways. First, you can deactivate it temporarily for your current "run cycle", that is after you have started your car and it's still running. Second, you completely deactivate the Belt Minder so that it never reminds you again, or at least until your reactivate it... The first method, temporary deactivation, or one time disable: After you have started your vehicle, buckle and then un-buckle your safety belt. Be sure to buckle back up.... This will disable the Belt Minder only for that ignition cycle. The second method, permanent deactivation: There are 9 steps you need to follow to deactivate or activate your Belt Minder system. Before doing so, make sure that: The parking brake is set. The truck/car is in Park (automatic), Neutral (manual). The ignition is OFF. All doors are closed. The driver's safety belt is un-buckled. The parking and headlights are OFF. Then follow these 9 steps: Turn the ignition switch to ON, but DO NOT START. Wait for the safety belt warning light to go OFF(1-2 minutes). Steps 3-5 MUST be completed within 60 seconds! Buckle, then un-buckle the driver's safety belt 3 times, ending with the belt un-buckled. Turn on the headlights, turn off the headlights. Buckle, then un-buckle the driver's safety belt 3 times, ending with the belt un-buckled. After step 5, the Safety Belt Warning Light will be turned on for 3 seconds. Within 7 seconds of the safety belt warning light turning OFF, buckle then un-buckle the safety belt. This will disable the Belt Minder if it is currently enabled, or enable the Belt Minder if it is currently disabled. Confirmation of the disabling of the Belt Minder is provided by flashing the safety belt warning light 4 times per seconds for 3 seconds. Confirmation of the enabling of the Belt Minder is provided by flashing the safety belt warning light 4 times per seconds for 3 seconds, followed by 3 seconds with the safety belt light off, then followed by flashing the safety belt light 4 times per second for 3 seconds again. After confirmation, the deactivation/activation of the Belt Minder procedure is complete.
How much money do civil air patrol pilots make?
Civil Air Patrol pilots do not make money. They are civilian volunteers.
Is it dangerous for a child to ride in a convertible car?
Its shouldn't be dangerous if the child is in the backseat with a seat belt, or if the child is of correct age for safety restrictions, in the front seat with a seat belt. Make sure the child isn't taking of his/her seat belt and/or leaning out of the car.
What fuse controls the seatbelt alarm on a 2005 Ford Escape?
Instaed of messing with the fuse, you can temporarily or permanently disable the seat belt alarm. Below is s copied instruction from a website on how to do it. Just remember all is at your own risk. You can Deactivate the Belt Minder two ways. First, you can deactivate it temporarily for your current "run cycle", that is after you have started your car and it's still running. Second, you completely deactivate the Belt Minder so that it never reminds you again, or at least until your reactivate it... The first method, temporary deactivation, or one time disable: After you have started your vehicle, buckle and then un-buckle your safety belt. Be sure to buckle back up.... This will disable the Belt Minder only for that ignition cycle. The second method, permanent deactivation: There are 9 steps you need to follow to deactivate or activate your Belt Minder system. Before doing so, make sure that: The parking brake is set. The truck/car is in Park (automatic), Neutral (manual). The ignition is OFF. All doors are closed. The driver's safety belt is un-buckled. The parking and headlights are OFF. Then follow these 9 steps: Turn the ignition switch to ON, but DO NOT START. Wait for the safety belt warning light to go OFF(1-2 minutes). Steps 3-5 MUST be completed within 60 seconds! Buckle, then un-buckle the driver's safety belt 3 times, ending with the belt un-buckled. Turn on the headlights, turn off the headlights. Buckle, then un-buckle the driver's safety belt 3 times, ending with the belt un-buckled. After step 5, the Safety Belt Warning Light will be turned on for 3 seconds. Within 7 seconds of the safety belt warning light turning OFF, buckle then un-buckle the safety belt. This will disable the Belt Minder if it is currently enabled, or enable the Belt Minder if it is currently disabled. Confirmation of the disabling of the Belt Minder is provided by flashing the safety belt warning light 4 times per seconds for 3 seconds. Confirmation of the enabling of the Belt Minder is provided by flashing the safety belt warning light 4 times per seconds for 3 seconds, followed by 3 seconds with the safety belt light off, then followed by flashing the safety belt light 4 times per second for 3 seconds again. After confirmation, the deactivation/activation of the Belt Minder procedure is complete
How do i disable seat belt sensor on ford focus zx3?
wear your seatbelt... or if you injoy going throuth your windshield at 60mph, just buckle the seatbelt and sit on top of it... Douglejg: Well actually you can disable it... if your car has electrical problems like my 2000 wagon, and your sensor doesn't work at all, this wont work... But i just ripped the thing out and wired it together so it thinks it always buckled.... Here is what i found online: The second method, permanent deactivation: Before starting, make sure that: The partking brake is set. The car is in Park(automatic), Neutral(manual). The ignition is OFF. All doors are closed. The driver's safety belt is un-buckled. The parking and headlights are OFF. 1) Turn the ignition switch to ON, but DO NOT START. 2) Wait for the safety belt warning light to go OFF(1-2 minutes). Steps 3-5 MUST be completed within 60 seconds! 3) Buckle, then un-buckle the driver's safety belt 3 times, ending with the belt un-buckled. 4) Turn on the headlights, turn off the headlights. 5) Buckle, then un-buckle the driver's safety belt 3 times, ending with the belt un-buckled. After step 5, the Safety Belt Warning Light will be turned on for 3 seconds. 6) Within 7 seconds of the safety belt warning light turning OFF, buckle then un-buckle the safety belt. This will disable the Belt Minder if it is currently enabled, or enable the Belt Minder if it is currently disabled. Confirmation of the disabling of the Belt Minder is provided by flashing the safety belt warning light 4 times per seconds for 3 seconds. Confirmation of the enabling of the Belt Minder is provided by flashing the safety belt warning light 4 times per seconds for 3 seconds, followed by 3 seconds with the safety belt light off, then followed by flashing the safety belt light 4 times per second for 3 seconds again. After confirmation, the deactivation/activation of the Belt Minder procedure is complete.
How much money does a marine patrol sargent in Maine make?
a marine patrol makes about $45,000, but a sargent for the marine patrols make about $60,000 to $70,000.
How can you disable a seat belt alarm in a 2000 Ford Crown Victoria?
Not to give you a trivial, smart aleck, P.I.T.A. (Pain In The 'rear') answer, but...Fasten your seatbelt! The seatbelt reminder alarm is there for your safety. Do not sit on top of a buckled safety belt to avoid the Belt Minder chime. Sitting on the safety belt will increase the risk of injury in an accident. To disable (one-time) or deactivate the Belt Minder feature please follow the directions stated below.Deactivating/activating the BeltMinder featureRead steps 1 - 9 thoroughly before proceeding with the deactivation/activation programming procedure.The BeltMinder feature can be deactivated/activated by performing the following procedure:Before following the procedure, make sure that:* The parking brake is set * The gearshift is in P (Park) (automatic transmission) * The ignition switch is in the OFF position * All vehicle doors are closed * The driver's safety belt is unbuckled * The parklamps/headlamps are in OFF position (If vehicle is equipped with Autolamps, this will not affect the procedure.)To reduce the risk of injury, do not deactivate/activate the BeltMinder feature while driving the vehicle.1. Turn the ignition switch to the RUN (or ON) position. (DO NOT START THE ENGINE)2. Wait until the safety belt warning light turns off. (Approximately 1-2 minutes)* Steps 3-5 must be completed within 60 seconds or the procedure will have to be repeated. 3. Buckle then unbuckle the safety belt three times, ending with the safety belt unbuckled. This can be done before or during BeltMinder warning activation.4. Turn on the parklamps/headlamps, turn off the parklamps/headlamps.5. Buckle then unbuckle the safety belt three times, ending with the safety belt unbuckled.* After step 5 the safety belt warning light will be turned on for three seconds. 6. Within seven seconds of the safety belt warning light turning off, buckle then unbuckle the safety belt.* This will disable BeltMinder if it is currently enabled, or enable BeltMinder if it is currently disabled.7. Confirmation of disabling BeltMinder is provided by flashing the safety belt warning light four times per second for three seconds.8. Confirmation of enabling BeltMinder is provided by flashing the safety belt warning light four times per second for three seconds, followed by three seconds with the safety belt warning light off, then followed by flashing the safety belt warning light four times per second for three seconds again.9. After receiving confirmation, the deactivation/activation procedure is complete.
How can you make the seat belt in a 2004 cavalier driver side longer?
Get a "Safety Belt Extender" at the Chevy dealer - for free. We got two of them. They had to order them, but it only took a couple of days. The owner's manual mentions this free option.
