1. Locate the Data Link Port. It is located under dash drivers side. Be sure you know which pins are 8 and 4. There are 16 pins on the port, you will notice one side of the port is wider than the other and the far left pin on the wide side is #1. They continue across to the right side which is #8, the row beneath that starts with #9(right below the #1 pin)and continues to the right finishing with pin #16. So it should look like this..... 1-2-3-(4)-5-6-7-(8) 9-10-11-12-13-14-15-16 (Notice port is wider on top row) 2. Make sure there are metal contact pins in terminals 8 and 4. Connect 8 to 4 with a suitable jumper wire (leave the jumper wire connected throughout the programming procedure). Make sure you know which terminals are 8 and 4. The vehicle will respond by locking and unlocking the doors to signify entering of programming mode. 3. Press and hold both the LOCK and UNLOCK buttons together on the first transmitter to be programmed. After about 15 seconds, the vehicle will respond by locking and unlocking the doors. Release the buttons on the transmitter. 4. Within one minute, repeat the previous step on the remaining transmitters to be programmed. 5. Remove jumper wire applied to the OBDII Port. 1. Locate the Data Link Port. It is located under dash drivers side. Be sure you know which pins are 8 and 4. There are 16 pins on the port, you will notice one side of the port is wider than the other and the far left pin on the wide side is #1. They continue across to the right side and ends with pin #8, the row beneath that starts with #9(right below the #1 pin)and continues to the right finishing with pin #16. So it should look like this..... 1-2-3-(4)-5-6-7-(8) 9-10-11-12-13-14-15-16 2.Make sure there are metal contact pins in terminals 8 and 4. Connect 8 to 4 with a suitable jumper wire (leave the jumper wire connected throughout the programming procedure. Make sure you know which terminals are 8 and 4. The vehicle will respond by locking and unlocking the doors to signify entering of programming mode. 3.Press and hold both the LOCK and UNLOCK buttons together on the first transmitter to be programmed. After about 15 seconds, the vehicle will respond by locking and unlocking the doors.Release the buttons on the transmitter. 4.Within one minute, repeat the previous step on the remaining transmitters to be programmed. 5.Remove jumper wire applied to the OBDII Port. 1. Locate the Data Link Port. It is located under dash drivers side. Be sure you know which pins are 8 and 4. There are 16 pins on the port, you will notice one side of the port is wider than the other and the far left pin on the wide side is #1. They continue across to the right side and ends with pin #8, the row beneath that starts with #9(right below the #1 pin)and continues to the right finishing with pin #16. So it should look like this..... 1-2-3-(4)-5-6-7-(8) 9-10-11-12-13-14-15-16 2.Make sure there are metal contact pins in terminals 8 and 4. Connect 8 to 4 with a suitable jumper wire (leave the jumper wire connected throughout the programming procedure. Make sure you know which terminals are 8 and 4. The vehicle will respond by locking and unlocking the doors to signify entering of programming mode. 3.Press and hold both the LOCK and UNLOCK buttons together on the first transmitter to be programmed. After about 15 seconds, the vehicle will respond by locking and unlocking the doors.Release the buttons on the transmitter. 4.Within one minute, repeat the previous step on the remaining transmitters to be programmed. 5.Remove jumper wire applied to the OBDII Port.
how do you program your keyless remote for 2003 Chevy blazer
How do i you program keyless remote for a 2004 malibu?
can soneone help me? i lost all my remote keyless entry for my 2003 Chevy express van and i just got a new repacement. but i don't know how to program it.. can soneone help?
How program my keyless entry remotes for 2003 chevy malibu
I have a use remote that I need to program
This vehicle requires a scan tool to program the remote, a dealer or locksmith will have to do it.
Try this site www.programyourremote.com
replaced battery and now remote doesnt work . how do you reprogram remote
programyourremote.com simply put.. "Program Your Remote.com"
Check out this site www.programyourremote.com .....
see also 2004 silverado
Look in your owners manual for the directions.