0
Your new pump should come with gaskets. just use blue silicone both sides & reattach with bolts. A little on the bolts threads might be a good call just in case. Some cars have 1 or more that go into the water jacket. Hand tight is fine. For the belt, just slip over all the pulleys you can & to get over the last one's pry on the idler(s) against the spring tension to move. A helper here comes in handy. Just ensure ribs on bottom of belt in proper grooves on pulleys. Routing diagram is usually on core support so all accessories turning right direction.
Wiki User
∙ 13y ago
Add your answer:
Earn +20 pts
How do you put the serpentine belt on a Chevy cavalier after you replaced the water pump?
opposite of the way you took it off before changing your water pump
How do you put on Serpentine belt on a 1998 Mazda protege?
This year Mazda protege does not have a serpentine belt. It has two belts, one for the alternator/water pump, and the other for the power steering and a/c.
How do you replace the water pump on a 1993 Mercury Tracer?
Well unfortunately the water pump is in behind the timing belt and the serpentine belt and you have to take all that off to get to the water pump. In the process of doing it now. Not a whole lot of room in there to work on. Once you replace the water pump, then you can put the timing belt back in (make sure timing marks are in place). Then move on to putting serpentine belt back on and all the rest that you had to remove to get to the water pump.
How do you change vw jetta glx water pump?
The water pump on a VW Jetta GLX water pump is changed by removing the serpentine belt, engine accessories, and radiator hoses. The pump is then unbolted, removed, and a new pump put in place.
How do you put on a 1988 Chevrolet Celebrity serpentine belt?
There should be a routing diagram under the hood. If it is the 2.8L V6 the diagram is on a guard above the belt between the power steering pump and the water pump.
How do you replace the water pump on a 94 Saturn sl1?
The water pump on a 94 Saturn S1 is replaced by removing the serpentine belt, engine accessories, and water hoses. The pump can then be unbolted from the engine block and a new pump put in place.
How do you change a 1988 Celebrity 2.8L water pump?
To change the water pump on a Chevy Celebrity 2.8L water pump 1987 to 1990: 1. Using a suitable drain pan loosen the drain and allow the coolant to drain. 2. Remove the belt guard above the water pump pulley. 3. Release the tension on the serpentine belt and remove the belt. Take careful note of the routing of the serpentine belt for replacement purposes. 4. Hold the water pump pulley still and remove the bolts that hold it in place. 5. Remove the bolts that hold the water pump in place and remove the pump. Clean the mounting surface so that a new gasket will seal. Using a new gasket install the replacement pump Reinstall the pulley and put the serpentine belt back in place' Put the belt guard back in place. Refill the radiator with coolant, check for leaks..
How do you put on a water pump belt on a 93 4-cylinder Cavalier?
Your water pump should run off of the serpentine belt. there shouldn't be a separate belt for the 4 cylinder. if you change the serpentine belt, there is a belt tentioner in the middle. using a wrench, not a ratchet(the ratchet will not have enough room to fully turn the tentioner), turn all the way to the right, remove the worn belt and replace it with a new one, following the belt diagram on the inside of the passengers side fender.
How do you replace water pump in an Au Ford Falcon 1999 model?
Not much different from earlier model falcons. First remove the thermo fans. Remove serpentine belt. Drain cooling system. Unbolt w/pump and clean surface. Bolt w/pump up Good time to change the serpentine belt if it's persished. Put fans in. Put coolant in and away you go. Easy.
Where is a serpentine belt routing diagram for a 1994 ford F150?
I need a diagram for a serpentine belt for a 1994 f150 with 5.0 engine I need a diagram for a serpentine belt for a 1994 f150 with 5.0 engine There should be a sticker near radiator shroud that has belt routing. If not stick the belt down past the right side of fan/water pump .put belt on crank pulley then pull back of belt over water pump and then down around power steering pulley and up over compressor pulley. put belt from crank pulley around smog pulley then up to tensioner with back of belt around tensioner and then around alternator pulley.next put rachet and socket(15 mm) on tensioner and pull on it while placing belt under idler pulley.
Removing the water pump from a 1987 Chevy Celebrity 2.5l?
To remove the water pump from a 1987 Chevy Celebrity: 1. Using a suitable container drain the coolant to a point below the water pump. 2. Release the tension on the serpentine belt. Remove the belt from the water pump pulley and position the belt away from the water pump. 3. Using a proper puller remove the pulley from the water pump. 4. Remove the bolts from the water pump. The water pump should pull off at this point To reinstall a new pump: 1. Clean the old gasket off the water pump mount point. 2. Using a new gasket and any sealer desired bolt the new pump in place. 3. Using the install tool press the pulley on the new pump. 4. Put the serpentine belt back in place. 5. Refill with coolant. Check for leaks
How do you change water pump 95 camaro 3.4 v6?
Take the serpentine belt off and then take off the water pump pulley and you will then see the bolts that hold the pump on, take the bolts out and pull the pump off, clean the surface on the engine real good and install new gasket on the new water pump with permetex to hold it in place and let dry for about 10 minutes, then reinstall pump with bolts and put pulley back on and finally the serpentine belt and refill the radiator opening the bleeder valve in back of the water pump and when you see fluid coming out of the valve close it back up.
