answersLogoWhite
Oldsmobile Bravada

How do you re-program a keyless remote for a 1998 Bravada?

102103104

Top Answer
User Avatar
Wiki User
2011-09-12 21:09:00
2011-09-12 21:09:00

1. Close all vehicle doors, windows up.2. Insert the key into the ignition and wait for dome light to turn off.3. Hold down the power unlock button on the driver's door panel - continue to hold down until instructed to release in step 94. erform steps 5 though 8 in fairly rapid succession.5. Turn the ignition switch to the on position (as far as you can go without starting the engine)6. Turn the ignition switch to the off position.7. Turn the ignition switch to the on position.8. Turn the ignition switch to the off position.9. Release the power unlock button on the door panel, The vehicle will cycle the door locks (lock and unlock the doors automatically) to indicate that the vehicle is in programming mode. IMPORTANT: ALL transmitters must be programmed at this time. When a new transmitter is programmed, it will deactivate the old transmitters.10. Press and hold the lock and unlock buttons on the transmitter simultaneously until the door locks cycle (locks and unlocks). This step may take up to 30 seconds.11. Repeat the previous step for each additional transmitter (including any existing transmitters).12. Turn the ignition switch to the on position in order to exit the transmitter programming mode.13. Test transmitter(s) for function.

1

Related Questions

User Avatar

I have a 98 Pontiac Transport and I had to reprogram my keyless enrty remote also. All I had to do is press and hold both lock and unlock buttons for about 5 seconds or until you hear the horn sound.

User Avatar

You cannot reprogram it. A dealer can get you the Master Code if you've lost it.

User Avatar

On the inside of the keyless entry remote or sometimes on the back it explains how to do this. I believe you hold the unlock button along with the lock button for 7 seconds near the car. It will explain it on the inside of the keyless entry remote.

User Avatar

Take the remote apart and it says to push the buttons once each or twice each try this

User Avatar

I bought a 1998 ford explorer and the owners manual showed how to reprogram the keyless entry system if you have the manual read it if not you can look on line for that info i had to locate the computer module to find the factory 5 # code on it before i could reprogram mine.May be different on 2008 just trying to help.

User Avatar

Your remote might need replaced, the buttons are probably worn out. They usually don't last for 10 years!

User Avatar

In the owners manual it tells. On my 93 lesabre I had to jump two of the connetors on the code reader

User Avatar

Try turning the ignition on and off about 10 times until the door locks, lock and unlock, then lock with the remote done.

User Avatar

The location of the remote keyless entry module on a 1998 Saturn is in the rear of the passenger compartment. It is underneath the trim at about shoulder height by the right rear seat.

User Avatar

My 98 Ram sport does it is a control module behind the dash if your does not and can be installed quick at the dealer .

User Avatar

First unlock and open the hatch, the horn alarm is now disarmed and you can unlock the driver side door.

User Avatar

To reset the computer on a 1998 Bravada you need to disconnect the negative cable from the battery. Leave off for 10 minutes and reattach.

User Avatar

If you need a new remote, you need to go to the dealer. If you have a remote that isn't working, replace the battery; stand next to your truck and push both "lock" and "unlock" buttons simultaneously until you hear the door locks cycle (about 4 seconds).

User Avatar

It should , my 1995 Explorer XLT has a keyless entry pad on the drivers door and came with 2 remotes

User Avatar

is there a fuel cut off switch in an oldsmobile bravada

User Avatar

In a 1998 Ford Explorer : The RAP module ( Remote Anti-theft Personality module ) is used with your anti-theft system and your keyless remotes ( each vehicle with keyless entry has it's own factory code )

User Avatar

The RKE module is located above the rear wheel well behind the driver's seat in the trunk.

User Avatar

What are the intake manifold torque specs on 1998 Oldsmobile bravada?"

User Avatar

My understanding is that you need to have it done at the dealer. There is no way of "cloning" an existing remote onto a second OEM one without dealer tools.

User Avatar

The keyless module is under the dash on the driver side. Do a search for Subaru Keyless Entry System H7110FS300

User Avatar

To change the license plate lamp on a 1998 Bravada, locate the bulb. Visit an auto parts store to obtain the exact bulb and screw it in place.

User Avatar

Keyless RemoteYou need to call the dealer. Get in the vehicle and close the door. Use the driver side lock switch to lock all the doors. Take the key and insert it into the ignition and remove it all the way 6 times with in 10 seconds. After you have done that press any button on the key fob. The lights should flash twice.

User Avatar

On front cover of engine by crankshaft pulley.


Copyright © 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.