0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
Why the received signal in analog communication is distorted by the channel noise than that of digital communication?
If an RF signal is AM modulated with a analogue signal any noise will add or subtract to the amplitude of the RF signal and will be present in the audio signal after detection, also will the noise add itself to the audio signal, where as in digital communication a slight variation in the amplitude of the signal is of no concern because you only work with ones and zeros, it's high or it's low
When signal amplitude is equal to carrier amplitude then modulation index is?
amplitude modulating signal
What will happen if frequency of modulating signal is greater than the carrier signal in amplitude modulation?
Then the signal will be the same amplitude.
What is the modulating frequency of amplitude modulation?
the frequency range of an am wave is 20herz to 20kilo herz
How does the intelligence signal modulates the carrier?
There are three major types of modulation:AM, Amplitude Modulation, where the modulation signal is altering the amplitude of the carrier according to its own amplitude, normally this is done in the output stage. Therefor a strong audio signal is necessary at the same or a little less than the power of the carrier, never higher, because that will over modulate the carrier that will resort in distortion of the receiver output. AM is used in the lower band of the RF spectrum.FM, Frequency Modulation, where the frequency of the carrier is altered by the audio signal. When the amplitude of the audio is going higher the frequency go lower. Modulation happen at the oscillator stage, therefor a small audio signal is used to modulate the frequency. FM is normally used in the higher frequency range of the RF spectrum, 50MHz and up.FSK, Frequency-shift keying, used for data transmission, this type of modulation is simply, switching the carrier on and of, a high bit will switch the oscillator on and a low bit will switch it off, in some designs a low will be on and a high off.
What is normalize audio?
The relative amplitude (loudness) of an audio signal can vary from soft to very loud. When you normalize an audio signal, you adjust the overall average amplitude to be about same throughout. An audio signal is 'normalized' to a specific numeric value, measured in decibels (e.g. -4db).
Why is amplitude of demodulated FM signal much less than modulated signal?
because demodulated FM is an audio signal, which the frequency is much smaller that is why it can be transmitted alone. It need carrier which has large frequency. Modulated signal is an audio signal + carrier that is why the amplitude is higher.
What is attueneter?
attenuator is a circuit which is used to reduce the amplitude of the signal.
What is over-modulating condition in term of amplitude modulation?
When your audio modulating signal is larger than your RF carrier amplitude the peak of the modulated carrier will become flat and a distorted audio signal with flattened peaks will be send out from the detector on the receiver side
Why the received signal in analog communication is distorted by the channel noise than that of digital communication?
If an RF signal is AM modulated with a analogue signal any noise will add or subtract to the amplitude of the RF signal and will be present in the audio signal after detection, also will the noise add itself to the audio signal, where as in digital communication a slight variation in the amplitude of the signal is of no concern because you only work with ones and zeros, it's high or it's low
Is the sample rate the number of times per second an audio signal's amplitude is measured and converted into a number?
yes
When signal amplitude is equal to carrier amplitude then modulation index is?
amplitude modulating signal
What is an AM transmitter?
Aplitude ModulationAn AM transmitter is a Amplitude Modulated transmitter where the amplitude of the Radio Frequency signal is modulated, usually used in the lower frequency bands where the frequency is to low for Frequency Modulation (FM), it was the first type of modulation used in radio communication FM was developed in the late 1950's and is not sensitive to static interference as AM AnswerAM is Amplitude Modulation that is the RF signals amplitude is modulated with the audio signal. this modulation is done because the audio signal being of low frequency cannot be transmitted to longer distance so the audio signal is amplitude modulated with RF signal and then transmitted into the air
What will happen if frequency of modulating signal is greater than the carrier signal in amplitude modulation?
Then the signal will be the same amplitude.
What is meant by repetition rate of the AM envelope?
The repetition rate of the amplitude modulation (AM) envelope refers to how often the modulation waveform repeats within a given unit of time. It indicates the frequency at which the carrier signal is modulated by the audio signal in an AM transmission. A higher repetition rate results in a faster fluctuation in the amplitude of the carrier signal.
Multiple choice question answer of AM modulation?
amplitude modulation is where we modulate our signal with a carrier signal amplitude changes but frequency remains constant in amplitude modulation
What is the modulating frequency of amplitude modulation?
the frequency range of an am wave is 20herz to 20kilo herz
