answersLogoWhite

0


Best Answer

To re-install a belt tensioner for a 1987 Ford Taurus, tighten the bolt when the tensioner pulley is holding the serpentine belt tight. The belt tensioner sits in a slot and can be adjusted to hold the belt tight.

User Avatar

Wiki User

โˆ™ 2014-09-18 00:14:14
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar

Add your answer:

Earn +20 pts
Q: How do you reinstall a belt tensioner for a 87 Ford Taurus?
Write your answer...
Submit
Related questions

How do you tighten an alternator belt on a 95 Ford Taurus?

You have to install a new belt tensioner.


How do you adjust the tension on the serpentine belt on a 1993 Ford Taurus?

Automatic tensioner- no adjustment required, or provided. If the tensioner is out of limits, replace the tensioner.


What to do when your belt tensioner wont move on 1999 Ford Taurus?

Pull it out and fit a new one


How do you tighten the fan belt on a 1998 Ford Taurus SE wagon?

It uses a spring loaded belt tensioner. The tensioner is autmatically set. IF there is not enough tension, then replace the tensioner. The belt may be stretched and need replacment however.


Serpentine belt keeps breaking on ford Taurus 2003?

Something is out of line. Check alternator, a/c pump, idler and tensioner. I've had 3 Taurus and never a single broken belt.


Where would the belt tensioner be located on a 1998 Ford Taurus when replacing the serpentine belt?

As viewing the motor from the front of the car, the belt tensioner is located on the left side of the engine. On what is essentially the front of the motor, the belt tensioner is located just below the idler pulley.


How do you tighten the belt tensioner on a 93 Taurus?

The tensioner has a spring in it that provides the correct tension for the belt. If it is too loose, replace the tensioner.


How do you install a cooling system belt on a 94 Ford Tempo?

# Install belt on to all pulleys except belt tensioner # Using the extension insert it into the belt tensioner and push away from you.Carefully install the ribbed belt on the tensioner and slowly allow the extension to move toward you as tension is placed on the belt # Remove extension from belt tensioner and inspect the belt to be sure it is seated correctly on all the pulleys if not remove belt and reinstall


Diagram for a belt on a 2005 Ford Taurus?

2005 ford taurus serpentine belt diagram


Where is the tensioner on a 97 Ford Escort?

there are two tensioners, the serpentine tensioner and the timing belt tensioner. the timing belt tensioner is behind the timing belt cover ;)


Where is the tensioner on a 2004 Ford Ranger?

where is the tensioner for the serpentine belt on a 2004 ford ranger


What is the diagram for 2001 Ford Taurus serpentine belt?

show me the diagram a 2001 ford taurus se fan belt


How do you put the belt back on the pulley assembly on a 95 Ford Taurus?

See "Related Questions" below for more about Taurus serpentine belts - both routing diagram sources and ideas on installing them. get the belt routed correctly, leaving a loop near the tensioner pulley. using a 15mm wrench on the tensioner bolt, move tensioner toward front of car (spring-loaded) slip smooth side of the belt over tensioner, release pressure on tensioner slowly. verify belt is fully seated before starting engine.


How do you tighten belts on a 2000 Ford Taurus?

By replacing the belt tensioner, this is a serpentine belt systems there is no adjusting the alternator bolt tighten the drive belts, if the belts are loose you must replace the belt tensioner and the belt to retain optimum performance from you Charging sytem as well as you other equipment being driven by the belt system.


How do you replace a belt tensioner on a 1996 for Taurus?

First, remove the coolant tank, then the belt. Unscrew the one bolt holding the tensioner in place. Installation is the reverse...


How do you change the serpentine belt on a 2001 Ford Ranger 6 cylinder and is there a square socket hole on the belt tensioner for using a ratchet handle?

the best way is use a breaker bar & cheater pipe & loosen tensioner remove belt be careful spring loaded go the same way to reinstall


Why does my Ford Taurus serpentine belt keep getting thew off?

Something is out of line, or you are using a warped belt. Take off and check the idler and also the tensioner pulley. They are most likely to cause belt problems.


Will a broken timing belt on a 99 Ford Taurus damage the engine?

The 1999 Ford Taurus does not have a timing belt. It has a chain that requires no maintenance.


How do you change a serpentine belt on a Mercury Sable - Ford Taurus?

(This answer Covers the Ford Motor Company Ford Taurus and Mercury Sable with the 3.0L OHV "Vulcan" Engine and the 3.0L DOHC "Duratec" engines.)Installation notes:Replace the belt by fitting it around the pulleys and lastly loosening the tension with the tensioner/idler pulley to allow the belt to fit over the last pulley. Attach a 15mm socket or wrench to the bolt in the middle of the tensioner pulley.On all 3.0L (OHV) engines, rotate the drive belt tensioner clockwise to relieve belt tension and slide the belt off the pulleys.On 3.0L (DOHC) engines, rotate the tensioner counter-clockwise to relieve belt tension and slide the belt off the pulleys.Replace the belt by fitting it around the pulleys and lastly loosening the tension with the tensioner/idler pulley to allow the belt to fit over the last pulley.AnswerPut a wrench on the (spring loaded) tensioner/ider pulley and take out the tension. You can then remove the belt. Replace the belt by fitting it around the pulleys and lastly loosening the tension with the tensioner/idler pulley to allow the belt to fit over the last pulley.


How do you reinstall the belt tensioner on a GM 5.7L G engine?

The opposite way you took it off


Where is the belt tensioner on a ford 2003 f350 6l diesel?

Where is the belt tensioner on a ford 2003 f350 6l diesel? i need to loosen so that i can replace the alternater


Where is the belt tensioner on 98 Ford Taurus?

right near the water pump passenger side.one big bolt removes it.remove serp bwlt 1st with belt removing tool or breaker bar.


How do you adjust the tension of the serpentine belt on a 1998 Ford Taurus with a 3.0 V6 engine?

You don't. The belt tensioner is spring loaded. If you look very very closely at the tensioner, there are wear-indicator marks that can confirm the belt has stretched beyond its useful life. See "Related Questions" below for more


How much would it cost to replace a serpentine belt tensioner on a 2003 Ford Taurus?

It cost me $183 at a private garage in Toronto, Ontario Canada (May 2012).


2001 Ford Escort cam timing belt tension?

Loosen the tensioner bolt, let the spring loaded tensioner contact the belt. Then tight the tensioner bolt.