answersLogoWhite

0


Best Answer

You just plug your nose and and try to to blow air out of it. kind of like blowing your nose underwater.

User Avatar

Wiki User

14y ago
This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: How do you relieve the pressure that you feel when you swim deep without going back to the surface?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Related questions

Why are your eyes drained?

Its what an optician does to relieve the pressure for a person who has glaucoma. A person with high pressures is at more risk of going blind, hence the procedure.


Where is the atmospheric pressure the greatest?

Near the earth's surface.


What is the definition of scratch the surface?

scratch the surface means going over something briefly without much detail.


Journal To Relieve Stress?

There are ways to relieve stress in your life without going to a doctor. Begin my keeping a journal and writing down your thoughts during the day. The ideal time to write things down is at night so you can get everything out of your mind before bed. A nice walk also clears the head of stresses, and promotes physical activity that will aid in relieving pressure from the body.


What happen to gas bubble volume as they rise in water?

As a bubble rises to the surface of a liquid the pressure on it is going DOWN. Therefore the bubble expands, and usually bursts at the surface.


How do you replace a 2005 Chevy cavalier serpantine belt?

you need to get a wrench and turn the bolt (relieve the pressure on the pulley) on the tensioner pulley and remove the belt then turn bolt (relieve the pressure on the pulley) to reinstall it. The tensioner pulley is the one that is not your A/C pulley not your alternator pulley and not your crankshaft pulley its the only one that's left no hoses or plugs going to it. not sure how to explain it.


How do you change 1991 Nissan Stanza fuel filter?

RELIEVE THE FUEL PRESSURE FIRST! I suggest going to Autozone.com and research it, but on my 1990 Stanza it involves pulling the fuse for the fuel pump, then cranking the engine until it dies, then crank it a few seconds to relieve it. if you don't relieve the pressure, you'll have 40 PSI of gas spraying out of the connection, which could start a fire or blind you. After the fuel pressure is gone, find the filter and remove then replace it with a new one, note the arrows on the filter for IN and OUT. Rplace the fuse, start the engine and look for leaks.


How do you relieve the fuel pressure to change the fuel filter on a 1999 CRV?

You don't. Just make sure the key is not on (best to not have it in the ignition at all) When you loosen the fuel filter, the pressure will relieve by leaking on the ground. Expect less than a half cup of fuel to leak out from pressure. The remainder fuel will be from inside the filter housing. Get ready to get your hands soaked in gasoline. Dont listen to that guy. You can relieve the gas pressure by simply open your gas cap and leave if off the entire time when you're working on your fuel filter. Some fuel will still leaks out from the fuel filter but at least it's not going to spray on your face.


What would happen if euglena did not have a contractile vacuole?

As the osmotic pressure of water, water going down it's concentration gradient, built up in the cell there would be increasing pressure on the cell membrane and without the vacuole to relieve this pressure the cell would burst.


Where can you find the fuel pressure regulator on a 1998 Ford Explorer with the 4.0 SOCH engine and how do you replace it?

The fuel pressure regulator is located on the fuel rail for the injectors. It should be right on top of the engine, and it will have a vacuum going to it. It is attached to the rail with two or three screws. Remember to relieve the fuel pressure first if you are planning on changing it.


What is back pressure?

Pressure going in the opposite direction in which it should be going.


How do you change a fuel filter for a 1994 jeep wrangler?

That's going to be on the drivers side, at the top of the rear wheel arch on the frame, just relieve pressure on the lines, loosen the clamps holding it in and fit the new one on.